75 lines
3.3 KiB
Plaintext
75 lines
3.3 KiB
Plaintext
HRTF Support
|
|
============
|
|
|
|
Starting with OpenAL Soft 1.14, HRTFs can be used to enable enhanced
|
|
spatialization for both 3D (mono) and multi-channel sources, when used with
|
|
headphones/stereo output. This can be enabled using the 'hrtf' config option.
|
|
|
|
For multi-channel sources this creates a virtual speaker effect, making it
|
|
sound as if speakers provide a discrete position for each channel around the
|
|
listener. For mono sources this provides much more versatility in the perceived
|
|
placement of sounds, making it seem as though they are coming from all around,
|
|
including above and below the listener, instead of just to the front, back, and
|
|
sides.
|
|
|
|
The default data set is based on the KEMAR HRTF data provided by MIT, which can
|
|
be found at <http://sound.media.mit.edu/resources/KEMAR.html>. It's only
|
|
available when using 44100hz or 48000hz playback.
|
|
|
|
|
|
Custom HRTF Data Sets
|
|
=====================
|
|
|
|
OpenAL Soft also provides an option to use user-specified data sets, in
|
|
addition to or in place of the default set. This allows users to provide their
|
|
own data sets, which could be better suited for their heads, or to work with
|
|
stereo speakers instead of headphones, or to support more playback sample
|
|
rates, for example.
|
|
|
|
The file format is specified below. It uses little-endian byte order.
|
|
|
|
==
|
|
ALchar magic[8] = "MinPHR01";
|
|
ALuint sampleRate;
|
|
|
|
ALubyte hrirSize; /* Can be 8 to 128 in steps of 8. */
|
|
ALubyte evCount; /* Can be 5 to 128. */
|
|
|
|
ALubyte azCount[evCount]; /* Each can be 1 to 128. */
|
|
|
|
/* NOTE: hrirCount is the sum of all azCounts */
|
|
ALshort coefficients[hrirCount][hrirSize];
|
|
ALubyte delays[hrirCount]; /* Each can be 0 to 63. */
|
|
==
|
|
|
|
The data is described as thus:
|
|
|
|
The file first starts with the 8-byte marker, "MinPHR01", to identify it as an
|
|
HRTF data set. This is followed by an unsigned 32-bit integer, specifying the
|
|
sample rate the data set is designed for (OpenAL Soft will not use it if the
|
|
output device's playback rate doesn't match).
|
|
|
|
Afterward, an unsigned 8-bit integer specifies how many sample points (or
|
|
finite impulse response filter coefficients) make up each HRIR.
|
|
|
|
The following unsigned 8-bit integer specifies the number of elevations used
|
|
by the data set. The elevations start at the bottom (-90 degrees), and
|
|
increment upwards. Following this is an array of unsigned 8-bit integers, one
|
|
for each elevation which specifies the number of azimuths (and thus HRIRs) that
|
|
make up each elevation. Azimuths start clockwise from the front, constructing
|
|
a full circle for the left ear only. The right ear uses the same HRIRs but in
|
|
reverse (ie, left = angle, right = 360-angle).
|
|
|
|
The actual coefficients follow. Each coefficient is a signed 16-bit sample,
|
|
with each HRIR being a consecutive number of sample points. The HRIRs must be
|
|
minimum-phase. This allows the use of a smaller filter length, reducing
|
|
computation. For reference, the built-in data set uses a 32-point filter while
|
|
even the smallest data set provided by MIT used a 128-sample filter (a 4x
|
|
reduction by applying minimum-phase reconstruction). Theoretically, one could
|
|
further reduce the minimum-phase version down to a 16-point filter with only a
|
|
small reduction in quality.
|
|
|
|
After the coefficients is an array of unsigned 8-bit delay values, one for
|
|
each HRIR. This is the propagation delay (in samples) a signal must wait before
|
|
being convolved with the corresponding minimum-phase HRIR filter.
|