Support usable check for all CPU features with the following changes:
1. Change struct cpu_features to
struct cpuid_features
{
struct cpuid_registers cpuid;
struct cpuid_registers usable;
};
struct cpu_features
{
struct cpu_features_basic basic;
struct cpuid_features features[COMMON_CPUID_INDEX_MAX];
unsigned int preferred[PREFERRED_FEATURE_INDEX_MAX];
...
};
so that there is a usable bit for each cpuid bit.
2. After the cpuid bits have been initialized, copy the known bits to the
usable bits. EAX/EBX from INDEX_1 and EAX from INDEX_7 aren't used for
CPU feature detection.
3. Clear the usable bits which require OS support.
4. If the feature is supported by OS, copy its cpuid bit to its usable
bit.
5. Replace HAS_CPU_FEATURE and CPU_FEATURES_CPU_P with CPU_FEATURE_USABLE
and CPU_FEATURE_USABLE_P to check if a feature is usable.
6. Add DEPR_FPU_CS_DS for INDEX_7_EBX_13.
7. Unset MPX feature since it has been deprecated.
The results are
1. If the feature is known and doesn't requre OS support, its usable bit
is copied from the cpuid bit.
2. Otherwise, its usable bit is copied from the cpuid bit only if the
feature is known to supported by OS.
3. CPU_FEATURE_USABLE/CPU_FEATURE_USABLE_P are used to check if the
feature can be used.
4. HAS_CPU_FEATURE/CPU_FEATURE_CPU_P are used to check if CPU supports
the feature.
A big shoutout to Cupertino Miranda <cmiranda@synopsys.com> for his
valuable contribution in initial bringup and debugging on Linux and
later in solving pesky unwinding/cancelation failures in testsuite.
Reviewed-by: Adhemerval Zanella <adhemerval.zanella@linaro.org>
Teach the linker that __mcount_internal, __sigjmp_save_symbol,
__syscall_error and __GI_exit do not use r2, so that it does not need to
recover r2 after the call.
Test at configure time if the assembler supports @notoc and define
USE_PPC64_NOTOC.
Make the instructions for syscall list generation match Makefile and
refer to `update-syscall-lists'; there has been no `update-arch-syscall'
target. Also use single quotes around the command to stick to the ASCII
character set.
Fixes 4cf0d22305 ("Linux: Add tables with system call numbers").
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
To provide a y2038 safe interface a new symbol __shmctl64 is added
and __shmctl is change to call it instead (it adds some extra buffer
copying for the 32 bit time_t implementation).
Two new structures are added:
1. kernel_shmid64_ds: used internally only on 32-bit architectures
to issue the syscall. A handful of architectures (hppa, i386,
mips, powerpc32, and sparc32) require specific implementations
due to their kernel ABI.
2. shmid_ds64: this is only for __TIMESIZE != 64 to use along with
the 64-bit shmctl. It is different than the kernel struct because
the exported 64-bit time_t might require different alignment
depending on the architecture ABI.
So the resulting implementation does:
1. For 64-bit architectures it assumes shmid_ds already contains
64-bit time_t fields and will result in just the __shmctl symbol
using the __shmctl64 code. The shmid_ds argument is passed as-is
to the syscall.
2. For 32-bit architectures with default 64-bit time_t (newer ABIs
such riscv32 or arc), it will also result in only one exported
symbol but with the required high/low time handling.
3. Finally for 32-bit architecture with both 32-bit and 64-bit time_t
support we follow the already set way to provide one symbol with
64-bit time_t support and implement the 32-bit time_t support
using of the 64-bit one.
The default 32-bit symbol will allocate and copy the shmid_ds
over multiple buffers, but this should be deprecated in favor
of the __shmctl64 anyway.
Checked on i686-linux-gnu and x86_64-linux-gnu. I also did some sniff
tests on powerpc, powerpc64, mips, mips64, armhf, sparcv9, and
sparc64.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Each architecture overrides the struct msqid_ds which its required
kernel ABI one.
Checked on x86_64-linux-gnu and some bases sysvipc tests on hppa,
mips, mipsle, mips64, mips64le, sparc64, sparcv9, powerpc64le,
powerpc64, and powerpc.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
This will allow us to have architectures specify their own version.
Not semantic changes expected. Checked with a build against the
all affected ABIs.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
To provide a y2038 safe interface a new symbol __msgctl64 is added
and __msgctl is change to call it instead (it adds some extra buffer
coping for the 32 bit time_t implementation).
Two new structures are added:
1. kernel_msqid64_ds: used internally only on 32-bit architectures
to issue the syscall. A handful of architectures (hppa, i386, mips,
powerpc32, and sparc32) require specific implementations due to
their kernel ABI.
2. msqid_ds64: this is only for __TIMESIZE != 64 to use along with
the 64-bit msgctl. It is different than the kernel struct because
the exported 64-bit time_t might require different alignment
depending on the architecture ABI.
So the resulting implementation does:
1. For 64-bit architectures it assumes msqid_ds already contains
64-bit time_t fields and will result in just the __msgctl symbol
using the __msgctl64 code. The msgid_ds argument is passed as-is
to the syscall.
2. For 32-bit architectures with default 64-bit time_t (newer ABIs
such riscv32 or arc), it will also result in only one exported
symbol but with the required high/low time handling.
3. Finally for 32-bit architecture with both 32-bit and 64-bit time_t
support we follow the already set way to provide one symbol with
64-bit time_t support and implement the 32-bit time_t support using
the 64-bit time_t.
The default 32-bit symbol will allocate and copy the msqid_ds
over multiple buffers, but this should be deprecated in favor
of the __msgctl64 anyway.
Checked on i686-linux-gnu and x86_64-linux-gnu. I also did some sniff
tests on powerpc, powerpc64, mips, mips64, armhf, sparcv9, and
sparc64.
Tested-by: Carlos O'Donell <carlos@redhat.com>
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Alistair Francis <alistair.francis@wdc.com>
Each architecture overrides the struct msqid_ds which its required
kernel ABI one.
Checked on x86_64-linux-gnu and some bases sysvipc tests on hppa,
mips, mipsle, mips64, mips64le, sparc64, sparcv9, powerpc64le,
powerpc64, and powerpc.
Tested-by: Carlos O'Donell <carlos@redhat.com>
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Alistair Francis <alistair.francis@wdc.com>
This will allow us to have architectures specify their own version.
Not semantic changes expected. Checked with a build against the
all affected ABIs.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
Different than others 64-bit time_t syscalls, the SysIPC interface
does not provide a new set of syscall for y2038 safeness. Instead it
uses unused fields in semid_ds structure to return the high bits for
the timestamps.
To provide a y2038 safe interface a new symbol __semctl64 is added
and __semctl is change to call it instead (it adds some extra buffer
copying for the 32 bit time_t implementation).
Two new structures are added:
1. kernel_semid64_ds: used internally only on 32-bit architectures
to issue the syscall. A handful of architectures (hppa, i386,
mips, powerpc32, sparc32) require specific implementations due
their kernel ABI.
2. semid_ds64: this is only for __TIMESIZE != 64 to use along with
the 64-bit semctl. It is different than the kernel struct because
the exported 64-bit time_t might require different alignment
depending on the architecture ABI.
So the resulting implementation does:
1. For 64-bit architectures it assumes semid_ds already contains
64-bit time_t fields and will result in just the __semctl symbol
using the __semctl64 code. The semid_ds argument is passed as-is
to the syscall.
2. For 32-bit architectures with default 64-bit time_t (newer ABIs
such riscv32 or arc), it will also result in only one exported
symbol but with the required high/low handling.
It might be possible to optimize it further to avoid the
kernel_semid64_ds to semun transformation if the exported ABI
for the architectures matches the expected kernel ABI, but the
implementation is already complex enough and don't think this
should be a hotspot in any case.
3. Finally for 32-bit architecture with both 32-bit and 64-bit time_t
support we follow the already set way to provide one symbol with
64-bit time_t support and implement the 32-bit time_t support
using the 64-bit one.
The default 32-bit symbol will allocate and copy the semid_ds
over multiple buffers, but this should be deprecated in favor
of the __semctl64 anyway.
Checked on i686-linux-gnu and x86_64-linux-gnu. I also did some sniff
tests on powerpc, powerpc64, mips, mips64, armhf, sparcv9, and
sparc64.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Vineet Gupta <vgupta@synopsys.com>
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
this means that *always* libnsl is only built as shared library for
backward compatibility and the NSS modules libnss_nis and libnss_nisplus
are not built at all, libnsl's headers aren't installed.
This compatibility is kept only for architectures and ABIs that have
been added in or before version 2.28.
Replacement implementations based on TIRPC, which additionally support
IPv6, are available from <https://github.com/thkukuk/>.
This change does not affect libnss_compat which does not depended
on libnsl since 2.27 and thus can be used without NIS.
libnsl code depends on Sun RPC, e.g. on --enable-obsolete-rpc (installed
libnsl headers use installed Sun RPC headers), which will be removed in
the following commit.
Binaries can opt-in to using BTI via an ELF object file marking.
The dynamic linker has to then mprotect the executable segments
with PROT_BTI. In case of static linked executables or in case
of the dynamic linker itself, PROT_BTI protection is done by the
operating system.
On AArch64 glibc uses PT_GNU_PROPERTY instead of PT_NOTE to check
the properties of a binary because PT_NOTE can be unreliable with
old linkers (old linkers just append the notes of input objects
together and add them to the output without checking them for
consistency which means multiple incompatible GNU property notes
can be present in PT_NOTE).
BTI property is handled in the loader even if glibc is not built
with BTI support, so in theory user code can be BTI protected
independently of glibc. In practice though user binaries are not
marked with the BTI property if glibc has no support because the
static linked libc objects (crt files, libc_nonshared.a) are
unmarked.
This patch relies on Linux userspace API that is not yet in a
linux release but in v5.8-rc1 so scheduled to be in Linux 5.8.
Co-authored-by: Szabolcs Nagy <szabolcs.nagy@arm.com>
Reviewed-by: Adhemerval Zanella <adhemerval.zanella@linaro.org>
setcontext returns to the specified context via an indirect jump,
so there should be a BTI j.
In case of getcontext (and all other returns_twice functions) the
compiler adds BTI j at the call site, but swapcontext is a normal
c call that is currently not handled specially by the compiler.
So we change swapcontext such that the saved context returns to a
local address that has BTI j and then swapcontext returns to the
caller via a normal RET. For this we save the original return
address in the slot for x1 of the context because x1 need not be
preserved by swapcontext but it is restored when the context saved
by swapcontext is resumed.
The alternative fix (which is done on x86) would make swapcontext
special in the compiler so BTI j is emitted at call sites, on
x86 there is an indirect_return attribute for this, on AArch64
we would have to use returns_twice. It was decided against because
such fix may need user code updates: the attribute has to be added
when swapcontext is called via a function pointer and it breaks
always_inline functions with swapcontext.
Reviewed-by: Adhemerval Zanella <adhemerval.zanella@linaro.org>
The strerrorname_np returns error number name (e.g. "EINVAL" for EINVAL)
while strerrordesc_np returns string describing error number (e.g
"Invalid argument" for EINVAL). Different than strerror,
strerrordesc_np does not attempt to translate the return description,
both functions return NULL for an invalid error number.
They should be used instead of sys_errlist and sys_nerr, both are
thread and async-signal safe. These functions are GNU extensions.
Checked on x86-64-linux-gnu, i686-linux-gnu, powerpc64le-linux-gnu,
and s390x-linux-gnu.
Tested-by: Carlos O'Donell <carlos@redhat.com>
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
The sigabbrev_np returns the abbreviated signal name (e.g. "HUP" for
SIGHUP) while sigdescr_np returns the string describing the error
number (e.g "Hangup" for SIGHUP). Different than strsignal,
sigdescr_np does not attempt to translate the return description and
both functions return NULL for an invalid signal number.
They should be used instead of sys_siglist or sys_sigabbrev and they
are both thread and async-signal safe. They are added as GNU
extensions on string.h header (same as strsignal).
Checked on x86-64-linux-gnu, i686-linux-gnu, powerpc64le-linux-gnu,
and s390x-linux-gnu.
Tested-by: Carlos O'Donell <carlos@redhat.com>
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
The buffer allocation uses the same strategy of strsignal.
Checked on x86-64-linux-gnu, i686-linux-gnu, powerpc64le-linux-gnu,
and s390x-linux-gnu.
Tested-by: Carlos O'Donell <carlos@redhat.com>
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
The per-thread state is refactored two use two strategies:
1. The default one uses a TLS structure, which will be placed in the
static TLS space (using __thread keyword).
2. Linux allocates via struct pthread and access it through THREAD_*
macros.
The default strategy has the disadvantage of increasing libc.so static
TLS consumption and thus decreasing the possible surplus used in
some scenarios (which might be mitigated by BZ#25051 fix).
It is used only on Hurd, where accessing the thread storage in the in
single thread case is not straightforward (afaiu, Hurd developers could
correct me here).
The fallback static allocation used for allocation failure is also
removed: defining its size is problematic without synchronizing with
translated messages (to avoid partial translation) and the resulting
usage is not thread-safe.
Checked on x86-64-linux-gnu, i686-linux-gnu, powerpc64le-linux-gnu,
and s390x-linux-gnu.
Tested-by: Carlos O'Donell <carlos@redhat.com>
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
The __NSIG_WORDS value is based on minimum number of words to hold
the maximum number of signals supported by the architecture.
This patch also adds __NSIG_BYTES, which is the number of bytes
required to represent the supported number of signals. It is used in
syscalls which takes a sigset_t.
Checked on x86_64-linux-gnu and i686-linux-gnu.
Tested-by: Carlos O'Donell <carlos@redhat.com>
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
The symbol is deprecated by strerror since its usage imposes some issues
such as copy relocations.
Its internal name is also changed to _sys_errlist_internal to avoid
static linking usage. The compat code is also refactored by removing
the over enginered errlist-compat.c generation from manual entried and
extra comment token in linker script file. It disantangle the code
generation from manual and simplify both Linux and Hurd compat code.
The definitions from errlist.c are moved to errlist.h and a new test
is added to avoid a new errno entry without an associated one in manual.
Checked on x86_64-linux-gnu and i686-linux-gnu. I also run a check-abi
on all affected platforms.
Tested-by: Carlos O'Donell <carlos@redhat.com>
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
The symbol was deprecated by strsignal and its usage imposes issues
such as copy relocations.
Its internal name is changed to __sys_siglist and __sys_sigabbrev to
avoid static linking usage. The compat code is also refactored, since
both Linux and Hurd usage the same strategy: export the same array with
different object sizes.
The libSegfault change avoids calling strsignal on the SIGFAULT signal
handler (the current usage is already sketchy, adding a call that
potentially issue locale internal function is even sketchier).
Checked on x86_64-linux-gnu and i686-linux-gnu. I also run a check-abi
on all affected platforms.
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
It refactor how signals are defined by each architecture. Instead of
include a generic header (bits/signum-generic.h) and undef non-default
values in an arch specific header (bits/signum.h) the new scheme uses a
common definition (bits/signum-generic.h) and each architectures add
its specific definitions on a new header (bits/signum-arch.h).
For Linux it requires copy some system default definitions to alpha,
hppa, and sparc. They are historical values and newer ports uses
the generic Linux signum-arch.h.
For Hurd the BSD signum is removed and moved to a new header (it is
used currently only on Hurd).
Checked on a build against all affected ABIs.
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
The variable is placed in libc.so, and it can be true only in
an outer libc, not libcs loaded via dlmopen or static dlopen.
Since thread creation from inner namespaces does not work,
pthread_create can update __libc_single_threaded directly.
Using __libc_early_init and its initial flag, implementation of this
variable is very straightforward. A future version may reset the flag
during fork (but not in an inner namespace), or after joining all
threads except one.
Reviewed-by: DJ Delorie <dj@redhat.com>
These tests validate that rseq is registered from various execution
contexts (main thread, destructor, other threads, other threads created
from destructor, forked process (without exec), pthread_atfork handlers,
pthread setspecific destructors, signal handlers, atexit handlers).
tst-rseq.c only links against libc.so, testing registration of rseq in
a non-multithreaded environment.
tst-rseq-nptl.c also links against libpthread.so, testing registration
of rseq in a multithreaded environment.
See the Linux kernel selftests for extensive rseq stress-tests.
When available, use the cpu_id field from __rseq_abi on Linux to
implement sched_getcpu(). Fall-back on the vgetcpu vDSO if unavailable.
Benchmarks:
x86-64: Intel E5-2630 v3@2.40GHz, 16-core, hyperthreading
glibc sched_getcpu(): 13.7 ns (baseline)
glibc sched_getcpu() using rseq: 2.5 ns (speedup: 5.5x)
inline load cpuid from __rseq_abi TLS: 0.8 ns (speedup: 17.1x)
Register rseq TLS for each thread (including main), and unregister for
each thread (excluding main). "rseq" stands for Restartable Sequences.
See the rseq(2) man page proposed here:
https://lkml.org/lkml/2018/9/19/647
Those are based on glibc master branch commit 3ee1e0ec5c.
The rseq system call was merged into Linux 4.18.
The TLS_STATIC_SURPLUS define is increased to leave additional room for
dlopen'd initial-exec TLS, which keeps elf/tst-auditmany working.
The increase (76 bytes) is larger than 32 bytes because it has not been
increased in quite a while. The cost in terms of additional TLS storage
is quite significant, but it will also obscure some initial-exec-related
dlopen failures.
The time argument is NULL in this case, and attempt to convert it
leads to a null pointer dereference.
This fixes commit d2e3b697da
("y2038: linux: Provide __settimeofday64 implementation").
Reviewed-by: Adhemerval Zanella <adhemerval.zanella@linaro.org>
This patch updates the kernel version in the test tst-mman-consts.py
to 5.7. (There are no new constants covered by this test in 5.7 that
need any other header changes; there's a new MREMAP_DONTUNMAP, but
this test doesn't yet cover MREMAP_*.)
Tested with build-many-glibcs.py.
1. Divide architecture features into the usable features and the preferred
features. The usable features are for correctness and can be exported in
a stable ABI. The preferred features are for performance and only for
glibc internal use.
2. Change struct cpu_features to
struct cpu_features
{
struct cpu_features_basic basic;
unsigned int *usable_p;
struct cpuid_registers cpuid[COMMON_CPUID_INDEX_MAX];
unsigned int usable[USABLE_FEATURE_INDEX_MAX];
unsigned int preferred[PREFERRED_FEATURE_INDEX_MAX];
...
};
and initialize usable_p to pointer to the usable arary so that
struct cpu_features
{
struct cpu_features_basic basic;
unsigned int *usable_p;
struct cpuid_registers cpuid[COMMON_CPUID_INDEX_MAX];
};
can be exported via a stable ABI. The cpuid and usable arrays can be
expanded with backward binary compatibility for both .o and .so files.
3. Add COMMON_CPUID_INDEX_7_ECX_1 for AVX512_BF16.
4. Detect ENQCMD, PKS, AVX512_VP2INTERSECT, MD_CLEAR, SERIALIZE, HYBRID,
TSXLDTRK, L1D_FLUSH, CORE_CAPABILITIES and AVX512_BF16.
5. Rename CAPABILITIES to ARCH_CAPABILITIES.
6. Check if AVX512_VP2INTERSECT, AVX512_BF16 and PKU are usable.
7. Update CPU feature detection test.
This patch changes the exp10f error handling semantics to only set
errno according to POSIX rules. New symbol version is introduced at
GLIBC_2.32. The old wrappers are kept for compat symbols.
There are some outliers that need special handling:
- ia64 provides an optimized implementation of exp10f that uses ia64
specific routines to set SVID compatibility. The new symbol version
is aliased to the exp10f one.
- m68k also provides an optimized implementation, and the new version
uses it instead of the sysdeps/ieee754/flt32 one.
- riscv and csky uses the generic template implementation that
does not provide SVID support. For both cases a new exp10f
version is not added, but rather the symbols version of the
generic sysdeps/ieee754/flt32 is adjusted instead.
Checked on aarch64-linux-gnu, x86_64-linux-gnu, i686-linux-gnu,
powerpc64le-linux-gnu.
Linux 5.7 has no new syscalls. Update the version number in
syscall-names.list to reflect that it is still current for 5.7.
Tested with build-many-glibcs.py.
timer_create needs to create threads with all signals blocked,
including SIGTIMER (which happens to equal SIGCANCEL).
Fixes commit b3cae39dcb ("nptl: Start
new threads with all signals blocked [BZ #25098]").
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
This introduces the function __pthread_attr_extension to allocate the
extension space, which is freed by pthread_attr_destroy.
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Linux overrides this file via sysdeps/unix/sysv/linux/i386/sysdep.c.
Hurd does not have sysdeps/unix/i386 on its search path, so it uses
csu/sysdep.c instead.
This is part of the libpthread removal project:
<https://sourceware.org/ml/libc-alpha/2019-10/msg00080.html>
Use __getline instead of __getdelim to avoid a localplt failure.
Likewise for __getrlimit/getrlimit.
The abilist updates were performed by:
git ls-files 'sysdeps/unix/sysv/linux/**/libc.abilist' \
| while read x ; do
echo "GLIBC_2.32 pthread_getattr_np F" >> $x
done
python3 scripts/move-symbol-to-libc.py --only-linux pthread_getattr_np
The private export of __pthread_getaffinity_np is no longer needed, but
the hidden alias still necessary so that the symbol can be exported with
versioned_symbol.
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
This is part of the libpthread removal project:
<https://sourceware.org/ml/libc-alpha/2019-10/msg00080.html>
The abilist updates were performed by:
git ls-files 'sysdeps/unix/sysv/linux/**/libc.abilist' \
| while read x ; do
echo "GLIBC_2.32 pthread_getaffinity_np F" >> $x
done
python3 scripts/move-symbol-to-libc.py pthread_getaffinity_np
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
This is part of the libpthread removal project:
<https://sourceware.org/ml/libc-alpha/2019-10/msg00080.html>
The symbol did not previously exist in libc, so a new GLIBC_2.32
symbol is needed, to get correct dependency for binaries which
use the symbol but no longer link against libpthread.
The abilist updates were performed by:
git ls-files 'sysdeps/unix/sysv/linux/**/libc.abilist' \
| while read x ; do
echo "GLIBC_2.32 pthread_attr_setaffinity_np F" >> $x
done
python3 scripts/move-symbol-to-libc.py pthread_attr_setaffinity_np
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
The stubs for pthread_getaffinity_np, pthread_getname_np,
pthread_setaffinity_np, pthread_setname_np are replaced, and corresponding
tests are moved.
After the removal of the NaCl port, nptl is Linux-specific, and the stubs
are no longer needed. This effectively reverts commit
c76d1ff514 ("NPTL: Add stubs for Linux-only
extension functions.").
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
This fixes a build error:
../sysdeps/unix/sysv/linux/ntp_gettime.c: In function ‘__ntp_gettime’:
../sysdeps/unix/sysv/linux/ntp_gettime.c:56:10: error: ‘ntv64.tai’ is used uninitialized in this function [-Werror=uninitialized]
56 | *ntv = valid_ntptimeval64_to_ntptimeval (ntv64);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The __clock_gettime internal function is not supporting 64 bit time on
architectures with __WORDSIZE == 32 and __TIMESIZE != 64 (like e.g. ARM 32
bit).
The __clock_gettime64 function shall be used instead in the glibc itself as
it supports 64 bit time on those systems.
This patch does not bring any changes to systems with __WORDSIZE == 64 as
for them the __clock_gettime64 is aliased to __clock_gettime (in
./include/time.h).
This patch provides new __ntp_gettimex64 explicit 64 bit function for getting
time parameters via NTP interface.
The call to __adjtimex in __ntp_gettime64 function has been replaced with
direct call to __clock_adjtime64 syscall, to simplify the code.
Moreover, a 32 bit version - __ntp_gettimex has been refactored to internally
use __ntp_gettimex64.
The __ntp_gettimex is now supposed to be used on systems still supporting 32
bit time (__TIMESIZE != 64) - hence the necessary conversions between struct
ntptimeval and 64 bit struct __ntptimeval64.
Build tests:
./src/scripts/build-many-glibcs.py glibcs
Run-time tests:
- Run specific tests on ARM/x86 32bit systems (qemu):
https://github.com/lmajewski/meta-y2038 and run tests:
https://github.com/lmajewski/y2038-tests/commits/master
Above tests were performed with Y2038 redirection applied as well as without to
test the proper usage of both __ntp_gettimex64 and __ntp_gettimex.
Reviewed-by: Adhemerval Zanella <adhemerval.zanella@linaro.org>
This patch provides new __ntp_gettime64 explicit 64 bit function for getting
time parameters via NTP interface.
Internally, the __clock_adjtime64 syscall is used instead of __adjtimex. This
patch is necessary for having architectures with __WORDSIZE == 32 Y2038 safe.
Moreover, a 32 bit version - __ntp_gettime has been refactored to internally
use __ntp_gettime64.
The __ntp_gettime is now supposed to be used on systems still supporting 32
bit time (__TIMESIZE != 64) - hence the necessary conversions between struct
ntptimeval and 64 bit struct __ntptimeval64.
Build tests:
./src/scripts/build-many-glibcs.py glibcs
Run-time tests:
- Run specific tests on ARM/x86 32bit systems (qemu):
https://github.com/lmajewski/meta-y2038 and run tests:
https://github.com/lmajewski/y2038-tests/commits/master
Above tests were performed with Y2038 redirection applied as well as without to
test the proper usage of both __ntp_gettime64 and __ntp_gettime.
Reviewed-by: Adhemerval Zanella <adhemerval.zanella@linaro.org>
Those functions allow easy conversion between Y2038 safe, glibc internal
struct __ntptimeval64 and struct ntptimeval.
The reserved fields (i.e. __glibc_reserved{1234}) during conversion are
zeroed as well, to provide behavior similar to one in ntp_gettimex function
(where those are cleared before the struct ntptimeval is returned).
Those functions are put in Linux specific sys/timex.h file, as putting
them into glibc's local include/time.h would cause build break on HURD as
it doesn't support struct timex related syscalls.
Build tests:
./src/scripts/build-many-glibcs.py glibcs
Reviewed-by: Adhemerval Zanella <adhemerval.zanella@linaro.org>
This type is a glibc's "internal" type to get time parameters data from
Linux kernel (NTP daemon interface). It stores time in struct __timeval64
rather than struct timeval, which makes it Y2038-proof.
Build tests:
./src/scripts/build-many-glibcs.py glibcs
Reviewed-by: Adhemerval Zanella <adhemerval.zanella@linaro.org>
