Resolves: #15424
The compiler would optimize the benchmark function call out of the
loop and call it only once, resulting in blazingly fast times for some
benchmarks (notably atan, sin and cos). Mark the inputs as volatile
so that the code is forced to read again from the input for each
iteration.
[BZ #15442] This adds support for the inverse interpretation of the
quiet bit of IEEE 754 floating-point NaN data that some processors
use. This includes in particular MIPS architecture processors; the
payload used for the canonical qNaN encoding is updated accordingly
so as not to interfere with the quiet bit.
The following patch fixes both _FPU_GETCW and
_FPU_SETCW for hppa. The initial implementation was
flawed and not well tested. We failed to set cw,
and passed in the value of a register to fldd.
This patch fixes both of those errors and allows
the libm tests to pass without failure.
Signed-off-by: Guy Martin <gmsoft@tuxicoman.be>
Signed-off-by: Carlos O'Donell <carlos@redhat.com>
---
2013-05-15 Guy Martin <gmsoft@tuxicoman.be>
Carlos O'Donell <carlos@redhat.com>
[BZ# 15000]
* ports/sysdeps/hppa/fpu/fpu_control.h (_FPU_GETCW): Set cw.
(_FPU_SETCW): Pass address to fldd.
Resolves#14888.
This only really manifests itself when there are no spaces between
format specifiers, which is not allowed by POSIX, but is allowed by
the glibc implementation.
Fixes#15346.
The POSIX description of getdate allows for extra spaces in the
getdate input string. __getdate_r uses strptime internally, which
works fine with extra spaces between format strings (and hence within
an input string) but not with leading and trailing spaces. So we trim
off the leading and trailing spaces before we pass it on to strptime.
The seen array was doubled in size recently, but the memset to clear
the array was not adjusted. We adjust the memset to always be correct
regardless of the size of seen.
---
2013-04-06 Carlos O'Donell <carlos@redhat.com>
[BZ #15309]
* elf/dl-open.c (dl_open_worker): memset all of seen array.
This change does two things:
* Treats a target i386-* as if it were i686.
* Fails configure if the user is generating code
for i386.
We no longer support i386 code-generation because the i386
lacks the atomic operations we need in glibc.
You can still configure for i386-*, but you get i686 code.
You can't build with --march=i386, --mtune=i386 or a compiler
that defaults to i386 code-generation.
I've added two i386 entries in the master todo list to discuss
merging and renaming:
http://sourceware.org/glibc/wiki/Development_Todo/Master#i386
The failure modes are fail-safe here. You compile for i386,
get i686, and try to run on i386 and it fails. The configure
log has a warning saying we elided to i686. There is no situation
that I can see where we run into any serious problems.
The patch makes the current state better in that we get less
confused users and we build successfully in more default
configurations.
The next enhancement would be to add --march=i?86
as suggested in #c20 of BZ#10062 for any i?86-* builds, which
would solve the problem of a 32-bit compiler that defaults to
i386 code-gen and glibc configured for i686-* target. Which
previously failed at build time, and now will fail at configure
time (requires adding --march=i686).
Updated NEWS with BZ #10060 and #10062.
No regressions.
---
2013-04-06 Carlos O'Donell <carlos@redhat.com>
[BZ #10060, #10062]
* aclocal.m4 (LIBC_COMPILER_BUILTIN_INLINED): New macro.
* sysdeps/i386/configure.in: Use LIBC_COMPILER_BUILTIN_INLINED and
fail configure if __sync_val_compare_and_swap is not inlined.
* sysdeps/i386/configure: Regenerate.
* configure.in: Build for i686 when configured for i386.
* configure: Regenerate.
* README: Remove i386 reference.
Fix BZ #15305.
On kernel versions earlier than 2.6.29, the Linux kernel exported a
sysctl called restrict_chown for xfs, which could be used to allow
chown to users other than the owner. 2.6.29 removed this support,
causing the open_not_cancel_2 to fail and thus modify errno. The fix
is to save and restore errno so that the caller sees it as unmodified.
Additionally, since the code to check the sysctl is not useful on
newer kernels, we add an ifdef so that in future the code block gets
rmeoved completely.
Fixes BZ #15304.
The *initgroups_dyn functions are called with a group argument. This
group gid is usually skipped while populating the grouplist since the
caller adds that group id in advance.
The hesiod initgroups_dyn implementation however adds the group gid to
the list if it does not already exist. While it works fine for the
usual initgroups, it breaks nscd since it calls initgroups_dyn with -1
as the gid (to have all groups included).
