This patch is an updated version of
<https://sourceware.org/ml/libc-alpha/2014-01/msg00198.html> and
<https://sourceware.org/ml/libc-alpha/2014-03/msg00180.html>.
Normal practice for software testsuites is that rather than
terminating immediately when a test fails, they continue running and
report at the end on how many tests passed or failed.
The principle behind the glibc testsuite stopping on failure was
probably that the expected state is no failures and so any failure
indicates a problem such as miscompilation. In practice, while this
is fairly close to true for native testing on x86_64 and x86 (kernel
bugs and race conditions can still cause intermittent failures), it's
less likely to be the case on other platforms, and so people testing
glibc run the testsuite with "make -k" and then examine the logs to
determine whether the failures are what they expect to fail on that
platform, possibly with some automation for the comparison.
This patch switches the glibc testsuite to the normal convention of
not stopping on failure - unless you use stop-on-test-failure=y, in
which case it behaves essentially as it did before (and does not
generate overall test summaries on failure). Instead, the summary
tests.sum may contain tests that FAILed. At the end of the test run,
any FAIL or ERROR lines from tests.sum are printed, and then it exits
with error status if there were any such lines. In addition, build
failures will also cause the test run to stop - this has the
justification that those *do* indicate serious problems that should be
promptly fixed and aren't generally hard to fix (but apart from that,
avoiding the build stopping on those failures seems harder).
Note that unlike the previous patches in this series, this *does*
require people with automation around testing glibc to change their
processes - either to start using tests.sum / xtests.sum to track
failures and compare them with expectations (with or without also
using "make -k" and examining "make" logs to identify build failures),
or else to use stop-on-test-failure=y and ignore the new tests.sum /
xtests.sum mechanism. (If all you check is the exit status from "make
check", no changes are needed unless you want to avoid test runs
continuing after the first failure.)
Tested x86_64.
* scripts/evaluate-test.sh: Handle fourth argument to determine
whether test run should stop on failure.
* Makeconfig (stop-on-test-failure): New variable.
(evaluate-test): Pass fourth argument to evaluate-test.sh based on
$(stop-on-test-failure).
* Makefile (tests): Give a summary of results from testing and
exit with failure status if they include an ERROR or FAIL.
(xtests): Likewise.
* manual/install.texi (Configuring and compiling): Mention
stop-on-test-failure=y.
* INSTALL: Regenerated.
The commit d136c6dc resulted in menu text for the "Top" node being added
to the INSTALL file on regeneration. As the full menu is not displayed
in the plain text file anyway, suppress the menu section completely to
avoid the additional text.
Also regenerate the INSTALL file to commit a small formatting change
introduced in the same commit.
Autoconf has been deprecating configure.in for quite a long time.
Rename all our configure.in and preconfigure.in files to .ac.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The pt-chown binary is discussed in the "Running make install" section
without clarification of the needed configure option. Clarify this
and simplfy the discription which is already covered in the "Configuring
and compiling" section.
The helper binary pt_chown tricked into granting access to another
user's pseudo-terminal.
Pre-conditions for the attack:
* Attacker with local user account
* Kernel with FUSE support
* "user_allow_other" in /etc/fuse.conf
* Victim with allocated slave in /dev/pts
Using the setuid installed pt_chown and a weak check on whether a file
descriptor is a tty, an attacker could fake a pty check using FUSE and
trick pt_chown to grant ownership of a pty descriptor that the current
user does not own. It cannot access /dev/pts/ptmx however.
In most modern distributions pt_chown is not needed because devpts
is enabled by default. The fix for this CVE is to disable building
and using pt_chown by default. We still provide a configure option
to enable hte use of pt_chown but distributions do so at their own
risk.
* configure: Regenerated.
* manual/install.texi (Tools for Compilation): Say 3.2 is required.
(Configuring and compiling): Don't mention older GCC versions any more.
* INSTALL: Regenerated.
* manual/install.texi (Configuring and compiling, Installation,
Running make install, Linux): Linux -> GNU/Linux where appropriate.
* elf/rtld.c (_dl_start_final): Move defn before _dl_start so it can
be inlined. Declare it with always_inline if [DONT_USE_BOOTSTRAP_MAP]
and with noinline otherwise. Remove hack alloca use to prevent
inlining, we can ask for it explicitly nowadays.
2000-08-09 Andreas Jaeger <aj@suse.de>
* configure.in: Change required make versions.
* manual/install.texi (Tools for Compilation): Document required
make version.
(Supported Configurations): Update list of supported
configurations.
* sysdeps/unix/sysv/linux/sys/raw.h (RAW_MAJOR): Added.
1999-09-08 Andreas Jaeger <aj@arthur.rhein-neckar.de>
* manual/install.texi (Configuring and compiling): Mention GCC 2.95.
1999-09-08 Andreas Jaeger <aj@arthur.rhein-neckar.de>
* configure.in: Fix make version test for make 3.77.95 and later
versions.
Based on a patch by Paul D. Smith <psmith@baynetworks.com>.
1999-09-10 Ulrich Drepper <drepper@cygnus.com>
