http://sourceware.org/ml/libc-alpha/2013-08/msg00089.html
Little-endian fixes for setjmp/longjmp. When writing these I noticed
the setjmp code corrupts the non volatile VMX registers when using an
unaligned buffer. Anton fixed this, and also simplified it quite a
bit.
The current code uses boilerplate for the case where we want to store
16 bytes to an unaligned address. For that we have to do a
read/modify/write of two aligned 16 byte quantities. In our case we
are storing a bunch of back to back data (consective VMX registers),
and only the start and end of the region need the read/modify/write.
[BZ #15723]
* sysdeps/powerpc/jmpbuf-offsets.h: Comment fix.
* sysdeps/powerpc/powerpc32/fpu/__longjmp-common.S: Correct
_dl_hwcap access for little-endian.
* sysdeps/powerpc/powerpc32/fpu/setjmp-common.S: Likewise. Don't
destroy vmx regs when saving unaligned.
* sysdeps/powerpc/powerpc64/__longjmp-common.S: Correct CR load.
* sysdeps/powerpc/powerpc64/setjmp-common.S: Likewise CR save. Don't
destroy vmx regs when saving unaligned.
http://sourceware.org/ml/libc-alpha/2013-08/msg00088.html
* sysdeps/powerpc/powerpc32/fpu/s_roundf.S: Increase alignment of
constants to usual value for .cst8 section, and remove redundant
high address load.
* sysdeps/powerpc/powerpc32/power4/fpu/s_llround.S: Use float
constant for 0x1p52. Load little-endian words of double from
correct stack offsets.
http://sourceware.org/ml/libc-alpha/2013-07/msg00201.html
These two functions oddly test x+1>0 when a double x is >= 0.0, and
similarly when x is negative. I don't see the point of that since the
test should always be true. I also don't see any need to convert x+1
to integer rather than simply using xr+1. Note that the standard
allows these functions to return any value when the input is outside
the range of long long, but it's not too hard to prevent xr+1
overflowing so that's what I've done.
(With rounding mode FE_UPWARD, x+1 can be a lot more than what you
might naively expect, but perhaps that situation was covered by the
x - xrf < 1.0 test.)
* sysdeps/powerpc/fpu/s_llround.c (__llround): Rewrite.
* sysdeps/powerpc/fpu/s_llroundf.c (__llroundf): Rewrite.
http://sourceware.org/ml/libc-alpha/2013-07/msg00200.html
This works around the fact that vsx is disabled in current
little-endian gcc. Also, float constants take 4 bytes in memory
vs. 16 bytes for vector constants, and we don't need to write one lot
of masks for double (register format) and another for float (mem
format).
* sysdeps/powerpc/fpu/s_float_bitwise.h (__float_and_test28): Don't
use vector int constants.
(__float_and_test24, __float_and8, __float_get_exp): Likewise.
http://sourceware.org/ml/libc-alpha/2013-07/msg00197.html
A rewrite to make this code correct for little-endian.
* sysdeps/ieee754/ldbl-128ibm/e_sqrtl.c (mynumber): Replace
union 32-bit int array member with 64-bit int array.
(t515, tm256): Double rather than long double.
(__ieee754_sqrtl): Rewrite using 64-bit arithmetic.
http://sourceware.org/ml/libc-alpha/2013-08/msg00085.html
Rid ourselves of ieee854.
* sysdeps/ieee754/ldbl-128ibm/ieee754.h (union ieee854_long_double):
Delete.
(IEEE854_LONG_DOUBLE_BIAS): Delete.
* sysdeps/ieee754/ldbl-128ibm/math_ldbl.h: Don't include ieee854
version of math_ldbl.h.
http://sourceware.org/ml/libc-alpha/2013-08/msg00084.html
Another batch of ieee854 macros and union replacement. These four
files also have bugs fixed with this patch. The fact that the two
doubles in an IBM long double may have different signs means that
negation and absolute value operations can't just twiddle one sign bit
as you can with ieee864 style extended double. fmodl, remainderl,
erfl and erfcl all had errors of this type. erfl also returned +1 for
large magnitude negative input where it should return -1. The hypotl
error is innocuous since the value adjusted twice is only used as a
flag. The e_hypotl.c tests for large "a" and small "b" are mutually
exclusive because we've already exited when x/y > 2**120. That allows
some further small simplifications.
[BZ #15734], [BZ #15735]
* sysdeps/ieee754/ldbl-128ibm/e_fmodl.c (__ieee754_fmodl): Rewrite
all uses of ieee875 long double macros and unions. Simplify test
for 0.0L. Correct |x|<|y| and |x|=|y| test. Use
ldbl_extract_mantissa value for ix,iy exponents. Properly
normalize after ldbl_extract_mantissa, and don't add hidden bit
already handled. Don't treat low word of ieee854 mantissa like
low word of IBM long double and mask off bit when testing for
zero.
* sysdeps/ieee754/ldbl-128ibm/e_hypotl.c (__ieee754_hypotl): Rewrite
all uses of ieee875 long double macros and unions. Simplify tests
for 0.0L and inf. Correct double adjustment of k. Delete dead code
adjusting ha,hb. Simplify code setting kld. Delete two600 and
two1022, instead use their values. Recognise that tests for large
"a" and small "b" are mutually exclusive. Rename vars. Comment.
* sysdeps/ieee754/ldbl-128ibm/e_remainderl.c (__ieee754_remainderl):
Rewrite all uses of ieee875 long double macros and unions. Simplify
test for 0.0L and nan. Correct negation.
* sysdeps/ieee754/ldbl-128ibm/s_erfl.c (__erfl): Rewrite all uses of
ieee875 long double macros and unions. Correct output for large
magnitude x. Correct absolute value calculation.
(__erfcl): Likewise.
* math/libm-test.inc: Add tests for errors discovered in IBM long
double versions of fmodl, remainderl, erfl and erfcl.
http://sourceware.org/ml/libc-alpha/2013-08/msg00083.html
Further replacement of ieee854 macros and unions. These files also
have some optimisations for comparison against 0.0L, infinity and nan.
Since the ABI specifies that the high double of an IBM long double
pair is the value rounded to double, a high double of 0.0 means the
low double must also be 0.0. The ABI also says that infinity and
nan are encoded in the high double, with the low double unspecified.
This means that tests for 0.0L, +/-Infinity and +/-NaN need only check
the high double.
* sysdeps/ieee754/ldbl-128ibm/e_atan2l.c (__ieee754_atan2l): Rewrite
all uses of ieee854 long double macros and unions. Simplify tests
for long doubles that are fully specified by the high double.
* sysdeps/ieee754/ldbl-128ibm/e_gammal_r.c (__ieee754_gammal_r):
Likewise.
* sysdeps/ieee754/ldbl-128ibm/e_ilogbl.c (__ieee754_ilogbl): Likewise.
Remove dead code too.
* sysdeps/ieee754/ldbl-128ibm/e_jnl.c (__ieee754_jnl): Likewise.
(__ieee754_ynl): Likewise.
* sysdeps/ieee754/ldbl-128ibm/e_log10l.c (__ieee754_log10l): Likewise.
* sysdeps/ieee754/ldbl-128ibm/e_logl.c (__ieee754_logl): Likewise.
* sysdeps/ieee754/ldbl-128ibm/e_powl.c (__ieee754_powl): Likewise.
Remove dead code too.
* sysdeps/ieee754/ldbl-128ibm/k_tanl.c (__kernel_tanl): Likewise.
* sysdeps/ieee754/ldbl-128ibm/s_expm1l.c (__expm1l): Likewise.
* sysdeps/ieee754/ldbl-128ibm/s_frexpl.c (__frexpl): Likewise.
* sysdeps/ieee754/ldbl-128ibm/s_isinf_nsl.c (__isinf_nsl): Likewise.
Simplify.
* sysdeps/ieee754/ldbl-128ibm/s_isinfl.c (___isinfl): Likewise.
Simplify.
* sysdeps/ieee754/ldbl-128ibm/s_log1pl.c (__log1pl): Likewise.
* sysdeps/ieee754/ldbl-128ibm/s_modfl.c (__modfl): Likewise.
* sysdeps/ieee754/ldbl-128ibm/s_nextafterl.c (__nextafterl): Likewise.
Comment on variable precision.
* sysdeps/ieee754/ldbl-128ibm/s_nexttoward.c (__nexttoward): Likewise.
* sysdeps/ieee754/ldbl-128ibm/s_nexttowardf.c (__nexttowardf):
Likewise.
* sysdeps/ieee754/ldbl-128ibm/s_remquol.c (__remquol): Likewise.
* sysdeps/ieee754/ldbl-128ibm/s_scalblnl.c (__scalblnl): Likewise.
* sysdeps/ieee754/ldbl-128ibm/s_scalbnl.c (__scalbnl): Likewise.
* sysdeps/ieee754/ldbl-128ibm/s_tanhl.c (__tanhl): Likewise.
* sysdeps/powerpc/fpu/libm-test-ulps: Adjust tan_towardzero ulps.
http://sourceware.org/ml/libc-alpha/2013-08/msg00081.html
This is the first of a series of patches to ban ieee854_long_double
and the ieee854_long_double macros when using IBM long double. union
ieee854_long_double just isn't correct for IBM long double, especially
when little-endian, and pretending it is OK has allowed a number of
bugs to remain undetected in sysdeps/ieee754/ldbl-128ibm/.
This changes the few places in generic code that use it.
* stdio-common/printf_size.c (__printf_size): Don't use
union ieee854_long_double in fpnum union.
* stdio-common/printf_fphex.c (__printf_fphex): Likewise. Use
signbit macro to retrieve sign from long double.
* stdio-common/printf_fp.c (___printf_fp): Use signbit macro to
retrieve sign from long double.
* sysdeps/ieee754/ldbl-128ibm/printf_fphex.c: Adjust for fpnum change.
* sysdeps/ieee754/ldbl-128/printf_fphex.c: Likewise.
* sysdeps/ieee754/ldbl-96/printf_fphex.c: Likewise.
* sysdeps/x86_64/fpu/printf_fphex.c: Likewise.
* math/test-misc.c (main): Don't use union ieee854_long_double.
ports/
* sysdeps/ia64/fpu/printf_fphex.c: Adjust for fpnum change.
http://sourceware.org/ml/libc-alpha/2013-06/msg00919.html
I discovered a number of places where denormals and other corner cases
were being handled wrongly.
- printf_fphex.c: Testing for the low double exponent being zero is
unnecessary. If the difference in exponents is less than 53 then the
high double exponent must be nearing the low end of its range, and the
low double exponent hit rock bottom.
- ldbl2mpn.c: A denormal (ie. exponent of zero) value is treated as
if the exponent was one, so shift mantissa left by one. Code handling
normalisation of the low double mantissa lacked a test for shift count
greater than bits in type being shifted, and lacked anything to handle
the case where the difference in exponents is less than 53 as in
printf_fphex.c.
- math_ldbl.h (ldbl_extract_mantissa): Same as above, but worse, with
code testing for exponent > 1 for some reason, probably a typo for >= 1.
- math_ldbl.h (ldbl_insert_mantissa): Round the high double as per
mpn2ldbl.c (hi is odd or explicit mantissas non-zero) so that the
number we return won't change when applying ldbl_canonicalize().
Add missing overflow checks and normalisation of high mantissa.
Correct misleading comment: "The hidden bit of the lo mantissa is
zero" is not always true as can be seen from the code rounding the hi
mantissa. Also by inspection, lzcount can never be less than zero so
remove that test. Lastly, masking bitfields to their widths can be
left to the compiler.
- mpn2ldbl.c: The overflow checks here on rounding of high double were
just plain wrong. Incrementing the exponent must be accompanied by a
shift right of the mantissa to keep the value unchanged. Above notes
for ldbl_insert_mantissa are also relevant.
[BZ #15680]
* sysdeps/ieee754/ldbl-128ibm/e_rem_pio2l.c: Comment fix.
* sysdeps/ieee754/ldbl-128ibm/printf_fphex.c
(PRINT_FPHEX_LONG_DOUBLE): Tidy code by moving -53 into ediff
calculation. Remove unnecessary test for denormal exponent.
* sysdeps/ieee754/ldbl-128ibm/ldbl2mpn.c (__mpn_extract_long_double):
Correct handling of denormals. Avoid undefined shift behaviour.
Correct normalisation of low mantissa when low double is denormal.
* sysdeps/ieee754/ldbl-128ibm/math_ldbl.h
(ldbl_extract_mantissa): Likewise. Comment. Use uint64_t* for hi64.
(ldbl_insert_mantissa): Make both hi64 and lo64 parms uint64_t.
Correct normalisation of low mantissa. Test for overflow of high
mantissa and normalise.
(ldbl_nearbyint): Use more readable constant for two52.
* sysdeps/ieee754/ldbl-128ibm/mpn2ldbl.c
(__mpn_construct_long_double): Fix test for overflow of high
mantissa and correct normalisation. Avoid undefined shift.
http://sourceware.org/ml/libc-alpha/2013-07/msg00001.html
This patch starts the process of supporting powerpc64 little-endian
long double in glibc. IBM long double is an array of two ieee
doubles, so making union ibm_extended_long_double reflect this fact is
the correct way to access fields of the doubles.
* sysdeps/ieee754/ldbl-128ibm/ieee754.h
(union ibm_extended_long_double): Define as an array of ieee754_double.
(IBM_EXTENDED_LONG_DOUBLE_BIAS): Delete.
* sysdeps/ieee754/ldbl-128ibm/printf_fphex.c: Update all references
to ibm_extended_long_double and IBM_EXTENDED_LONG_DOUBLE_BIAS.
* sysdeps/ieee754/ldbl-128ibm/e_exp10l.c: Likewise.
* sysdeps/ieee754/ldbl-128ibm/e_expl.c: Likewise.
* sysdeps/ieee754/ldbl-128ibm/ldbl2mpn.c: Likewise.
* sysdeps/ieee754/ldbl-128ibm/math_ldbl.h: Likewise.
* sysdeps/ieee754/ldbl-128ibm/mpn2ldbl.c: Likewise.
* sysdeps/ieee754/ldbl-128ibm/s_nearbyintl.c: Likewise.
* sysdeps/ieee754/ldbl-128ibm/strtold_l.c: Likewise.
* sysdeps/ieee754/ldbl-128ibm/x2y2m1l.c: Likewise.
[BZ #15915] As described in the bug, the pattern rule for lib%.so files
in Makerules includes linkobj/libc.so as a dependency. However, the
explicit rule for linkobj/libc.so is in the top-level Makefile.
Thus, the subdirectory makefiles that include Makerules end up with an
erroneous makefile pattern rule for linkobj/libc.so that includes
itself as a dependency. The result is make warnings whenever rules
for other .so files are resolved -- and, on occasion, actual makefile
failures when a race condition causes the implicit rule to actually be
used.
This patch moves the explicit rules for linkobj/libc.so into Makerules
to clear up this problem. It also elaborates a couple of comments
that I'd initially found confusing.
Colin Watson reported that some versions of gcc warn about
attribute leaf used on a static function, since it has no
effect on anything but external functions.
* posix/glob.c (next_brace_sub, prefix_array, collated_compare):
Use __THROWNL rather than __THROW on static functions.
Signed-off-by: Eric Blake <eblake@redhat.com>
sysdeps/unix/make-syscalls.sh and sysdeps/unix/Makefile use GNU Bash's
${parameter/pattern/string} parameter expansion. Non-Bash shells (e.g.
dash or BusyBox ash when built with CONFIG_ASH_BASH_COMPAT disabled)
don't support this expansion syntax. So glibc will fail to build when
$(SHELL) expands to a path that isn't provided by Bash.
An example build failure:
for dir in [...]; do \
test -f $dir/syscalls.list && \
{ sysdirs='[...]' \
asm_CPP='gcc -c -I[...] -D_LIBC_REENTRANT -include include/libc-symbols.h -DASSEMBLER -g -Wa,--noexecstack -E -x assembler-with-cpp' \
/bin/sh sysdeps/unix/make-syscalls.sh $dir || exit 1; }; \
test $dir = sysdeps/unix && break; \
done > [build-dir]/sysd-syscallsT
sysdeps/unix/make-syscalls.sh: line 273: syntax error: bad substitution
This patch simply replaces the three instances of the Bash-only syntax
in these files with an echo and sed command substitution.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This define was removed from the rest of the tree eight years ago.
ChangeLog:
2013-09-24 Will Newton <will.newton@linaro.org>
* sysdeps/mach/hurd/i386/tls.h (TLS_INIT_TP_EXPENSIVE): Remove
macro.
strcoll is implemented using a cache for indices and weights of
collation sequences in the strings so that subsequent passes do not
have to search through collation data again. For very large string
inputs, the cache size computation could overflow. In such a case,
use the fallback function that does not cache indices and weights of
collation sequences.
Fixes CVE-2012-4412.
strcoll currently falls back to alloca if malloc fails, resulting in a
possible stack overflow. This patch implements sequence traversal and
comparison without caching indices and rules.
Fixes CVE-2012-4424.
Statically built binaries use __pointer_chk_guard_local,
while dynamically built binaries use __pointer_chk_guard.
Provide the right definition depending on the test case
we are building.
The pointer guard used for pointer mangling was not initialized for
static applications resulting in the security feature being disabled.
The pointer guard is now correctly initialized to a random value for
static applications. Existing static applications need to be
recompiled to take advantage of the fix.
The test tst-ptrguard1-static and tst-ptrguard1 add regression
coverage to ensure the pointer guards are sufficiently random
and initialized to a default value.
