for ChangeLog
* malloc/arena.c (new_heap): New memory_heap_new probe.
(grow_heap): New memory_heap_more probe.
(shrink_heap): New memory_heap_less probe.
(heap_trim): New memory_heap_free probe.
* malloc/malloc.c (sysmalloc): New memory_sbrk_more probe.
(systrim): New memory_sbrk_less probe.
* manual/probes.texi: Document them.
It has been a long practice for software using IEEE 754 floating-point
arithmetic run on MIPS processors to use an encoding of Not-a-Number
(NaN) data different to one used by software run on other processors.
And as of IEEE 754-2008 revision [1] this encoding does not follow one
recommended in the standard, as specified in section 6.2.1, where it
is stated that quiet NaNs should have the first bit (d1) of their
significand set to 1 while signalling NaNs should have that bit set to
0, but MIPS software interprets the two bits in the opposite manner.
As from revision 3.50 [2][3] the MIPS Architecture provides for
processors that support the IEEE 754-2008 preferred NaN encoding format.
As the two formats (further referred to as "legacy NaN" and "2008 NaN")
are incompatible to each other, tools have to provide support for the
two formats to help people avoid using incompatible binary modules.
The change is comprised of two functional groups of features, both of
which are required for correct support.
1. Dynamic linker support.
To enforce the NaN encoding requirement in dynamic linking a new ELF
file header flag has been defined. This flag is set for 2008-NaN
shared modules and executables and clear for legacy-NaN ones. The
dynamic linker silently ignores any incompatible modules it
encounters in dependency processing.
To avoid unnecessary processing of incompatible modules in the
presence of a shared module cache, a set of new cache flags has been
defined to mark 2008-NaN modules for the three ABIs supported.
Changes to sysdeps/unix/sysv/linux/mips/readelflib.c have been made
following an earlier code quality suggestion made here:
http://sourceware.org/ml/libc-ports/2009-03/msg00036.html
and are therefore a little bit more extensive than the minimum
required.
Finally a new name has been defined for the dynamic linker so that
2008-NaN and legacy-NaN binaries can coexist on a single system that
supports dual-mode operation and that a legacy dynamic linker that
does not support verifying the 2008-NaN ELF file header flag is not
chosen to interpret a 2008-NaN binary by accident.
2. Floating environment support.
IEEE 754-2008 features are controlled in the Floating-Point Control
and Status (FCSR) register and updates are needed to floating
environment support so that the 2008-NaN flag is set correctly and
the kernel default, inferred from the 2008-NaN ELF file header flag
at the time an executable is loaded, respected.
As the NaN encoding format is a property of GCC code generation that is
both a user-selected GCC configuration default and can be overridden
with GCC options, code that needs to know what NaN encoding standard it
has been configured for checks for the __mips_nan2008 macro that is
defined internally by GCC whenever the 2008-NaN mode has been selected.
This mode is determined at the glibc configuration time and therefore a
few consistency checks have been added to catch cases where compilation
flags have been overridden by the user.
The 2008 NaN set of features relies on kernel support as the in-kernel
floating-point emulator needs to be aware of the NaN encoding used even
on hard-float processors and configure the FPU context according to the
value of the 2008 NaN ELF file header flag of the executable being
started. As at this time work on kernel support is still in progress
and the relevant changes have not made their way yet to linux.org master
repository.
Therefore the minimum version supported has been artificially set to
10.0.0 so that 2008-NaN code is not accidentally run on a Linux kernel
that does not suppport it. It is anticipated that the version is
adjusted later on to the actual initial linux.org kernel version to
support this feature. Legacy NaN encoding support is unaffected, older
kernel versions remain supported.
[1] "IEEE Standard for Floating-Point Arithmetic", IEEE Computer
Society, IEEE Std 754-2008, 29 August 2008
[2] "MIPS Architecture For Programmers, Volume I-A: Introduction to the
MIPS32 Architecture", MIPS Technologies, Inc., Document Number:
MD00082, Revision 3.50, September 20, 2012
[3] "MIPS Architecture For Programmers, Volume I-A: Introduction to the
MIPS64 Architecture", MIPS Technologies, Inc., Document Number:
MD00083, Revision 3.50, September 20, 2012
Only enter the aligned copy loop with buffers that can be 8-byte
aligned. This improves performance slightly on Cortex-A9 and
Cortex-A15 cores for large copies with buffers that are 4-byte
aligned but not 8-byte aligned.
ports/ChangeLog.arm:
2013-09-16 Will Newton <will.newton@linaro.org>
* sysdeps/arm/armv7/multiarch/memcpy_impl.S: Tighten check
on entry to aligned copy loop to improve performance.
The TIMING_INIT macro currently sets the number of loop iterations
to 1000, which limits usefulness. Make the argument a clock
resolution value and multiply by 1000 in bench-skeleton.c instead
to allow easier reuse.
ChangeLog:
2013-09-11 Will Newton <will.newton@linaro.org>
* benchtests/bench-timing.h (TIMING_INIT): Rename ITERS
parameter to RES. Remove hardcoded 1000 value.
* benchtests/bench-skeleton.c (main): Pass RES parameter
to TIMING_INIT and multiply result by 1000.
A large bytes parameter to memalign could cause an integer overflow
and corrupt allocator internals. Check the overflow does not occur
before continuing with the allocation.
ChangeLog:
2013-09-11 Will Newton <will.newton@linaro.org>
[BZ #15857]
* malloc/malloc.c (__libc_memalign): Check the value of bytes
does not overflow.
A large bytes parameter to valloc could cause an integer overflow
and corrupt allocator internals. Check the overflow does not occur
before continuing with the allocation.
ChangeLog:
2013-09-11 Will Newton <will.newton@linaro.org>
[BZ #15856]
* malloc/malloc.c (__libc_valloc): Check the value of bytes
does not overflow.
A large bytes parameter to pvalloc could cause an integer overflow
and corrupt allocator internals. Check the overflow does not occur
before continuing with the allocation.
ChangeLog:
2013-09-11 Will Newton <will.newton@linaro.org>
[BZ #15855]
* malloc/malloc.c (__libc_pvalloc): Check the value of bytes
does not overflow.
The end of the "Parsing of Floats" subsection currently reads:
The GNU C Library also provides '_l' versions of these functions,
which take an additional argument, the locale to use in conversion.
*Note Parsing of Integers::.
Split the final note as it is unrelated to the above comment and
reference it with "See also" instead.
The pt-chown binary is discussed in the "Running make install" section
without clarification of the needed configure option. Clarify this
and simplfy the discription which is already covered in the "Configuring
and compiling" section.
