Instead of using a boolean to indicate a modal operation being in progress,
use a set of flags, and allow these to be set and unset independently.
Specifically, this allows WM_CAPTURECHANGED handler to only act when a drag-move or
drag-resize modal operation is in progress, and ignore DND (which can also cause
WM_CAPTURECHANGED to be posted). This avoids a crash due to assertion failure when
OLE2 DND code tries to end a modal operation that was already ended by the WM_CAPTURECHANGED
handler.
(This commit is cherry-picked from the gtk-3-22 branch)
https://bugzilla.gnome.org/show_bug.cgi?id=786121
Commit 1d0fad3 revealed that there were some assumptions made that were
actually to compensate for the bug fixed by that commit, so we need to
remove those assumptions as they would result in AerSnap to not work
properly on HiDPI screens.
Also re-do how we set the x and y positions of our GdkWindow, so that we
are more consistent across the board when we go between a GDK window
coordinate and a Windows API window cooredinate.
This would also simplify the code a bit.
https://bugzilla.gnome.org/show_bug.cgi?id=785999
Some drivers don't do that (not sure whether that is the correct behaviour
or not). Remember each WT_PROXIMITY with LOWORD(lParam) != 0 that we get,
then look for a WT_CSRCHANGE. If WT_CSRCHANGE doesn't come, but a WT_PACKET
does, assume that this device is the one that sent WT_PROXIMITY.
Also include fallback code to ensure that WT_PACKETs for an enabled device
disable the system pointer, because WT_PROXIMITY handler might have
enabled it by mistake, since it's not possible to know which device left
the proximity (it might have been a disabled device).
https://bugzilla.gnome.org/show_bug.cgi?id=778328
Previously HiDPI scale was retrieved and applied too late in the initialization
process to affect monitor size and monitor workarea size, but the code that
initializes these sizes *did* try to use the scale, even though it was always
getting scale=1.
To fix this, move the too-late code into monitor enumeration routine.
This also fixes a probable semantic bug where width and height were divided
by scale, again.
Now monitor and workarea should be in application pixels (i.e. divided by scale),
as intended.
https://bugzilla.gnome.org/show_bug.cgi?id=778835
Previously GDK only made up monitors when it initially found none. Now it
also makes up monitors when it initially finds some, but later fails to get
their informatin in a normal way and finally prunes them out, being left with
zero monitors.
Having zero-length monitor array is unexpected and causes a number
of critical warnings and some critical functionality (such as displaying
drop-down menus) fails in such cases.
Ideally, there might be such a way to interrogate W32 API that produces the
information about non-real (but active) monitors out of it so that it isn't
necessary for us to make stuff up. However, this code is already complicated,
and i am not prepared to dig W32 API to find a way to do this.
This fixes the issues people had when they accessed a Windows desktop via RDP.
https://bugzilla.gnome.org/show_bug.cgi?id=777527
Windows WM handles AeroSnap for normal windows on keydown. We did this
on keyup only because we do not get a keydown message, even if Windows WM
does nothing with a combination. However, in some specific cases it DOES
do something - and we have no way to detect that. Specifically, winkey+downarrow
causes maximized window to be restored by WM, and GDK fails to detect that. Then
GDK gets a keyup message, figures that winkey+downarrow was pressed and released,
and handles the combination - by minimizing the window.
To overcome this, install a low-level keyboard hook (high-level ones have
the same problem as normal message loop - they don't get messages when
Windows WM handles combinations) and use it to detect interesting key combinations
before Windows WM has a chance to block them from being processed.
Once an interesting combination is detected, post a message to the window, which
will be handled in due order.
It should be noted that this code handles key repetitions in a very crude manner.
The downside is that AeroSnap will not work if hook installation function call fails.
Also, this is a global hook, and if the hook procedure does something wrong, bad things
can happen.
https://bugzilla.gnome.org/show_bug.cgi?id=776031
Instead of using some kind of flawed logic about modifying a keypress result
when CapsLock is toggled, just add a CapsLock shift level (and all derived
shift levels, i.e. Shift+CapsLock and CapsLock+AltGr and Shift+CapsLock+AltGr)
and query Windows keyboard layout API about the result of keypresses involving
CapsLock.
Keysym table is going to be (roughly) twice as large now, but CapsLock'ed
keypresses will give correct results for some keyboard layouts (such as
Czech keyboard layout, which without this change produces lowercase letters
for CapsLock->[0,2,3,4...] instead of uppercase ones).
Keymap update time also increases accordingly.
https://bugzilla.gnome.org/show_bug.cgi?id=165385
Instead of checking for window state and giving it extra styles that
fit, just give it all styles that it is missing. It turned out that
otherwise it is impossible to, for example, restore a maximized window
via sysmenu. Also, be more flexible towards GDK/WM window state mismatches
and consider the window minimized/maximized if *either* GDK or WM thinks so.
https://bugzilla.gnome.org/show_bug.cgi?id=776485
Just set check_for_dpi_awareness = TRUE and eventually it will be handled
correctly, even if setDpiAwareFunc() returns E_ACCESSDENIED or shcore functions
are NULL.
https://bugzilla.gnome.org/show_bug.cgi?id=777031
When primary monitor is smaller than the actual monitor on which the
window is being maximized, the WM will do widnow size adjustments
that will completely screw the window size if we try to make it
smaller than 100% fullscreen (to account for taskbar size, for example).
Fix this by overriding maximized window size during WM_WINDOWPOSCHANGING.
https://bugzilla.gnome.org/show_bug.cgi?id=775808
The wayland backend currently never emits GDK_SELECTION_CLEAR events.
GtkClipboard uses this signal in order to clear the clipboard owner when
the selection is set to something outside the application.
This commit ensures the wayland backend emits GDK_SELECTION_CLEAR before
setting the clipboard owner to NULL, as this means we lost the
selection.
Signed-off-by: Christophe Fergeau <cfergeau@redhat.com>
https://bugzilla.gnome.org/show_bug.cgi?id=790031
