diff --git a/doc/lz4_Block_format.md b/doc/lz4_Block_format.md index dd4c91b..5438730 100644 --- a/doc/lz4_Block_format.md +++ b/doc/lz4_Block_format.md @@ -1,6 +1,6 @@ LZ4 Block Format Description ============================ -Last revised: 2015-05-07. +Last revised: 2018-04-25. Author : Yann Collet @@ -29,8 +29,8 @@ An LZ4 compressed block is composed of sequences. A sequence is a suite of literals (not-compressed bytes), followed by a match copy. -Each sequence starts with a token. -The token is a one byte value, separated into two 4-bits fields. +Each sequence starts with a `token`. +The `token` is a one byte value, separated into two 4-bits fields. Therefore each field ranges from 0 to 15. @@ -42,46 +42,46 @@ If it is 15, then we need to add some more bytes to indicate the full length. Each additional byte then represent a value from 0 to 255, which is added to the previous value to produce a total length. When the byte value is 255, another byte is output. -There can be any number of bytes following the token. There is no "size limit". +There can be any number of bytes following `token`. There is no "size limit". (Side note : this is why a not-compressible input block is expanded by 0.4%). -Example 1 : A length of 48 will be represented as : +Example 1 : A literal length of 48 will be represented as : - 15 : value for the 4-bits High field - 33 : (=48-15) remaining length to reach 48 -Example 2 : A length of 280 will be represented as : +Example 2 : A literal length of 280 will be represented as : - 15 : value for the 4-bits High field - 255 : following byte is maxed, since 280-15 >= 255 - 10 : (=280 - 15 - 255) ) remaining length to reach 280 -Example 3 : A length of 15 will be represented as : +Example 3 : A literal length of 15 will be represented as : - 15 : value for the 4-bits High field - 0 : (=15-15) yes, the zero must be output -Following the token and optional length bytes, are the literals themselves. +Following `token` and optional length bytes, are the literals themselves. They are exactly as numerous as previously decoded (length of literals). It's possible that there are zero literal. Following the literals is the match copy operation. -It starts by the offset. +It starts by the `offset`. This is a 2 bytes value, in little endian format (the 1st byte is the "low" byte, the 2nd one is the "high" byte). -The offset represents the position of the match to be copied from. +The `offset` represents the position of the match to be copied from. 1 means "current position - 1 byte". -The maximum offset value is 65535, 65536 cannot be coded. +The maximum `offset` value is 65535, 65536 cannot be coded. Note that 0 is an invalid value, not used. -Then we need to extract the match length. +Then we need to extract the `matchlength`. For this, we use the second token field, the low 4-bits. Value, obviously, ranges from 0 to 15. However here, 0 means that the copy operation will be minimal. -The minimum length of a match, called minmatch, is 4. +The minimum length of a match, called `minmatch`, is 4. As a consequence, a 0 value means 4 bytes, and a value of 15 means 19+ bytes. Similar to literal length, on reaching the highest possible value (15), we output additional bytes, one at a time, with values ranging from 0 to 255. @@ -90,18 +90,18 @@ A 255 value means there is another byte to read and add. There is no limit to the number of optional bytes that can be output this way. (This points towards a maximum achievable compression ratio of about 250). -Decoding the matchlength reaches the end of current sequence. +Decoding the `matchlength` reaches the end of current sequence. Next byte will be the start of another sequence. But before moving to next sequence, it's time to use the decoded match position and length. -The decoder copies matchlength bytes from match position to current position. +The decoder copies `matchlength` bytes from match position to current position. -In some cases, matchlength is larger than offset. -Therefore, match pos + match length > current pos, +In some cases, `matchlength` is larger than `offset`. +Therefore, `match_pos + matchlength > current_pos`, which means that later bytes to copy are not yet decoded. This is called an "overlap match", and must be handled with special care. -The most common case is an offset of 1, -meaning the last byte is repeated matchlength times. +A common case is an offset of 1, +meaning the last byte is repeated `matchlength` times. Parsing restrictions @@ -114,19 +114,23 @@ with assumptions made by the decoder : bytes) must be encoded as literals on behalf of the last sequence. The last sequence is incomplete, and stops right after the literals. 2. The last match must start at least 12 bytes before end of block. - Consequently, a block with less than 13 bytes cannot be compressed. + The last match is part of the penultimate sequence, + since the last sequence stops right after literals. + Note that, as a consequence, blocks < 13 bytes cannot be compressed. These rules are in place to ensure that the decoder -will never read beyond the input buffer, nor write beyond the output buffer. +can speculatively execute copy instructions +without ever reading nor writing beyond provided I/O buffers. 1. To copy literals from a non-last sequence, an 8-byte copy instruction - can always be safely issued (without reading past the input), because - the literals are followed by a 2-byte offset, and the last sequence - is at least 1+5 bytes long. -2. TODO: explain the benefits of the second restriction. + can always be safely issued (without reading past the input), + because literals are followed by a 2-byte offset, + and last sequence is at least 1+5 bytes long. +2. Similarly, a match operation can speculatively copy up to 12 bytes + while remaining within output buffer boundaries. -Empty inputs are either unrepresentable or can be represented with a null byte, -which can be interpreted as a token without literals and without a match. +Empty inputs can be represented with a zero byte, +interpreted as a token without literals and without a match. Additional notes