as a side effect, this fixes the generators that were more bitrotted
(nmake and even more mingw).
Task-number: QTBUG-30644 #close
Change-Id: Iefa3f07125884412d091aa12b44935e5b1fb858a
Reviewed-by: Rafael Roquetto <rafael.roquetto@kdab.com>
Reviewed-by: Joerg Bornemann <joerg.bornemann@digia.com>
unlike unix' mkdir -p, windows' md complains if the directory already
exists. the workaround is a quite complex command, so the so far used
concept for assembling the command line from pieces was replaced with a
single template. for symmetry, adapt the makefile existence check to the
new concept as well.
QMAKE_CHK_EXISTS and QMAKE_MKDIR_CMD were added, with hard-coded
fallbacks (ugly).
QMAKE_CHK_FILE_EXISTS and QMAKE_CHK_EXISTS_GLUE (introduced in 5.0.0)
are simply deleted again.
QMAKE_CHK_DIR_EXISTS and QMAKE_MKDIR remain for legacy reasons, as qmake
emits them into the Makefiles, and custom commands may rely on their
presence.
Task-number: QTBUG-28132
Change-Id: I3d049cb5d26947e5c3d102d0c2da33afb2a95140
Reviewed-by: Joerg Bornemann <joerg.bornemann@digia.com>
Reviewed-by: Janne Anttila <janne.anttila@digia.com>
Reviewed-by: Kai Koehne <kai.koehne@digia.com>
d28073d9 creates a distinction between "mac" and
"macx". The latter is not set on iOS, which caused
MakefileGenerator::target_mode to be set to TARG_UNIX_MODE.
Check for the "mac" active config instead of "macx".
Rename TARG_MACX_MODE -> TARG_MAC_MODE.
Change-Id: I7192788c33f5723034ba76da2492379dd454f0ab
Reviewed-by: Oswald Buddenhagen <oswald.buddenhagen@digia.com>
Reviewed-by: Tor Arne Vestbø <tor.arne.vestbo@digia.com>
Metafiles such as .prl and .pc files contain paths that have to be
adjusted during installation. The same code is used for unix and
windows so move it into the base class.
Change-Id: I82db89ec83820a4fa0214ba15e7cd63438f6dc91
Reviewed-by: Oswald Buddenhagen <oswald.buddenhagen@digia.com>
Change copyrights and license headers from Nokia to Digia
Change-Id: If1cc974286d29fd01ec6c19dd4719a67f4c3f00e
Reviewed-by: Lars Knoll <lars.knoll@digia.com>
Reviewed-by: Sergio Ahumada <sergio.ahumada@digia.com>
this is preparation for adapting to a new evaluator.
Change-Id: I6fc59f5525735754a00afa6629fbfe257e84db97
Reviewed-by: Daniel Teske <daniel.teske@nokia.com>
Reviewed-by: Joerg Bornemann <joerg.bornemann@nokia.com>
instead of re-assembling a list from the variables, take the original
command line minus some explicitly stripped out options. this is way
less code and poses no synchronization problem between the two parts.
as a "side effect", variables obtained from $QMAKEFLAGS won't multiply
with each makefile nesting level, as the generated command line won't
replicate data obtained from the environment.
Change-Id: I5d1ce0f11efb338f60405529f9818910103b1b0e
Reviewed-by: Joerg Bornemann <joerg.bornemann@nokia.com>
Remove references to an old compiler that has not been
supported for a long time. Also remove Borland specific
configuration flags which have no meaning elsewhere.
Change-Id: I3634a52b78f737ea972073e14c2b6669dcd0ae63
Reviewed-by: Oswald Buddenhagen <oswald.buddenhagen@nokia.com>
the visitor-pattern like approach is not needed any more
Change-Id: I990db681cbeee91d89ecba97745a8104595247e7
Reviewed-by: Friedemann Kleint <Friedemann.Kleint@nokia.com>
Reviewed-by: Joerg Bornemann <joerg.bornemann@nokia.com>
it's more elegant, and more similar code is better.
Change-Id: I2b8b036cb70a932fd171e23cf7d3389188401924
Reviewed-by: Friedemann Kleint <Friedemann.Kleint@nokia.com>
Reviewed-by: Joerg Bornemann <joerg.bornemann@nokia.com>
Use XOR instead of OR in order to avoid saturating all bits when computing the
hash value.
Change-Id: I50b1a044eb827239dae1c04732ca6a065f6233b4
Reviewed-by: Andreas Holzammer <andreas.holzammer@kdab.com>
Reviewed-by: Oswald Buddenhagen <oswald.buddenhagen@nokia.com>
it's a tad insane to expect the user to do that
Change-Id: I75c68f2a28656c9ba2e3fabcc79718b899b29ce7
Reviewed-by: Joerg Bornemann <joerg.bornemann@nokia.com>
the project evaluator becomes oblivious of the target mode.
the mode is set up in spec_post.prf according to the spec.
$$QMAKE_TARGET contains the feature suffixes to search, and is also
contained in $$CONFIG.
the target_mode variable itself becomes private to the Makefile class.
Change-Id: I3c06d9dab536b753343cec6c5c491d3203e50bd8
Reviewed-by: Mark Brand <mabrand@mabrand.nl>
the only callers which used non-default arguments are gone now, so remove
the arguments entirely. this also enables us to re-enable result caching.
Change-Id: I62f76e17e531a4eeafddb9b29716ca0a0eb3dbea
Reviewed-by: Thiago Macieira <thiago.macieira@intel.com>
Reviewed-by: Joerg Bornemann <joerg.bornemann@nokia.com>
the specs in Option are now only fixifiable absolute paths if an actual
path was passed on the command line - otherwise these are just names,
and we should pass them on verbatim.
Change-Id: I5b3535dadf2d6b2b3116331e6636f6e363a5361f
Reviewed-by: Thiago Macieira <thiago.macieira@intel.com>
Reviewed-by: Joerg Bornemann <joerg.bornemann@nokia.com>
instead of making the "real" targets depend on the makefiles, add
conditional makefile generation to the targets themselves.
this causes makefile generation to follow the recursion order determined
by the project, which is important when dealing with prl and module pri
files.
a side effect of this is that qmake and make calls are interleaved now,
which is entirely different from a 'qmake -r' run.
on the downside, calling make with multiple targets which operate on the
same subprojects without prior makefile generation will make a mess, as
the qmake calls will be racing. this should be no problem, as qmake does
not generate recursive targets where this would be useful - at least by
default.
it is not sufficient to just order the creation of the makefiles
non-recursively (e.g., by using gnu-specific order-only-prerequisites),
as an interrupted and subsequently resumed build would happily skip the
nested makefiles.
workable alternative approaches would be walking the entire tree in a
pre-pass to ensure makefile presence (which is incredibly slow) or
creating additional stamp files only after recursing and having the
makefiles depend on them (which is ugly).
Task-number: QTBUG-23376
Reviewed-by: Joerg Bornemann <joerg.bornemann@nokia.com>
Change-Id: I88d3e7610215677d362026de316513d3bea04b06
instead of hard-coding platform differences, use a variable.
Change-Id: I20e98811ad5f07429148c6f88aedbabc3ba58fff
Reviewed-by: Joerg Bornemann <joerg.bornemann@nokia.com>
no need to define an obscure variable for it. just inline it.
the assignments are left in for compatibility with hand-written commands.
Change-Id: I9bc3914e2c4116f3b8fe00a421ca0f036bb7e214
Reviewed-by: Joerg Bornemann <joerg.bornemann@nokia.com>
so far it would rebuild the makefiles one level down only, which is
somewhat arbitrary and not really helpful.
Change-Id: I5fe01f379ecc4b210610a674d7df7dfc18131eef
Reviewed-by: Joerg Bornemann <joerg.bornemann@nokia.com>
Reviewed-by: Oswald Buddenhagen <oswald.buddenhagen@nokia.com>
when qmake runs into the new option(host_build) command, it will restart
the project evaluation with a host spec.
the new default host spec is called default-host (gasp!). it is
overridden with the pre-exising -spec / -platform option, while the new
-xspec / -xplatform option overrides the pre-existing default spec.
specifying -spec but not -xspec will set the xspec, too, so the behavior
is backwards-compatible. same for the XQMAKESPEC override read from
.qmake.cache and the environment variable.
the cleaner solution would be adding -hostspec, to be symmetrical with
the override semantics, but that would deviate from configure in turn.
Change-Id: I4297c873780af16ab7928421b434ce0f1d3820da
Reviewed-by: Joerg Bornemann <joerg.bornemann@nokia.com>
this was a somewhat magic support for sysroots, automatically rewriting
a number of path-holding variables. this was (as usual) completely
undocumented, extremely fragile, and we are coming up with something
better now anyway.
Change-Id: I045910f532cb3efc839ea81c7a48f8db695e4092
Reviewed-by: Joerg Bornemann <joerg.bornemann@nokia.com>
As in the past, to avoid rewriting various autotests that contain
line-number information, an extra blank line has been inserted at the
end of the license text to ensure that this commit does not change the
total number of lines in the license header.
Change-Id: I311e001373776812699d6efc045b5f742890c689
Reviewed-by: Rohan McGovern <rohan.mcgovern@nokia.com>
And enable this configuration option for the resource compiler. This
results in a re-run of qmake whenever you touch a qrc file, which is
needed to keep the dependencies up to date. Otherwise you might end
up in the situation where you add a file to a qrc, edit the file some
time later, but a rebuild does not regenerate a cpp file and compile
that, so the final binary is stale.
Technically this dependency problem is present for all source files,
and qrc files are no different than any cpp file that you add a new
header #include to, or adding a Q_OBJECT macro to a header. To pick
up these changes we have to re-run qmake, so that qmake can run its
internal dependency checking, and any extra compiler dependency
commands.
The reason we're making this change for rcc files it that conceptually
people treat them as a "project" files, and expect them to behave similarly
to .pro or .pri files, in that editing the file will invalidate the
makefile. In practice this is often what happens when adding new
headers, as you touch the project file when changing the HEADERS
variable.
Task-number: QTBUG-13334
Change-Id: If69149678e7fba6d812d31dcc17877427f9a6122
Reviewed-by: Simon Hausmann <simon.hausmann@nokia.com>
Reviewed-by: Kai Koehne <kai.koehne@nokia.com>
This is the beginning of revision history for this module. If you
want to look at revision history older than this, please refer to the
Qt Git wiki for how to use Git history grafting. At the time of
writing, this wiki is located here:
http://qt.gitorious.org/qt/pages/GitIntroductionWithQt
If you have already performed the grafting and you don't see any
history beyond this commit, try running "git log" with the "--follow"
argument.
Branched from the monolithic repo, Qt master branch, at commit
896db169ea224deb96c59ce8af800d019de63f12
