We hope this shall avoid some flaky failures noticed in quick tests,
e.g. tst_QQuickMenu::Material::subMenuPosition(cascading,flip) was
recently seen failing with 3.88e-11 != 0. This required some revision
to test data in the testlib selftest for floats; the resulting
expected output differs in details but not in which tests pass or
fail. QEMU, naturally, made life difficult, requiring special-case
code in the test-driver.
[ChangeLog][QtTestLib][QCOMPARE] QCOMPARE() now treats its values as
equal when qFuzzyIsNull() is true for both of them.
Change-Id: Icc6ad5164b609937eddbe39cc69120f0abf0f3b4
Reviewed-by: Qt CI Bot <qt_ci_bot@qt-project.org>
Reviewed-by: Mitch Curtis <mitch.curtis@qt.io>
In QCOMPARE, handle NaNs and infinities the way tests want them
handled, rather than by strict IEEE rules. In particular, if a test
expects NaN, this lets it treat that just like any other expected
value, despite NaN != NaN as float16 values. Likewise, format
infinities and NaNs specially in toString() so that they're reported
consistently.
Enable the qfloat16 tests that depend on this QCOMPARE() behavior.
Refise the testlib selftest's float test to test qfloat16 the same way
it tests float and double (and format the test the same way).
This is a follow-up to 37f617c405.
Change-Id: I433256a09b1657e6725d68d07c5f80d805bf586a
Reviewed-by: Thiago Macieira <thiago.macieira@intel.com>
The QTest::qCompare() implementations were almost duplicates; pull the
common code out into a templated version. Tweaked the
QTest::toString() specialization for float and double (a macro) and
fixed a bous modifier in double's format.
The doubleComparisons and floatComparisons tests in the tst_float.cpp
selftest shared a large block of tests in common, aside from the
difference of type. Break this out into a templated static function
to save duplication.
This prepares the way for using the same templated code for qfloat16.
Change-Id: I2823fd006910c5ff88335d625d1fa05cb7753513
Reviewed-by: Thiago Macieira <thiago.macieira@intel.com>
Tidied up the existing float tests in the process.
(In particular, s/SUCCESS/PASS/ since that matches real test output.)
These verify that QCOMPARE() handles floats and doubles as intended.
Extended the existing qFuzzyCompare tests to probe the boundaries of
the ranges of values of both types, in the process.
Revised the toString<double> that qCompare() uses to give enough
precision to actually show some of the differences being tested there
(12 digits, to match what qFuzzyCompare tests, so as to show different
values rather than, e.g. 1e12 for both expected and actual) and to
give consistent results for infinities and NaN (MinGW had eccentric
versions for these, leading to different output from tests, which thus
failed); did the latter also for toString<float> and fixed stray zeros
in MinGW's exponents (which made a kludge in tst_selftest.cpp
redundant, so I removed that, too).
That's further complicated handling of floating-point types, so let's
just keep an eye on how expensive that's getting by adding a benchmark
test for QTest::toString(). Unfortunately, default settings only get
runs that take modest numbers of milliseconds (some as low as 40)
while increasing this with -minumumvalue 100 or more gets the process
killed - and I'm unable to find out who's doing the killing (it's not
QProcess::kill, ::kill or the QtTest WatchDog, as far as I can tell).
So results are rather noisy; the integral tests exhibit speed-ups by
factors up to 5, and slow-downs by factors up to 100, between runs
with and without this change, which does not affec the integral tests.
The relatively modest slow-downs and speed-ups in the floating point
tests thus seem likely to be happenstance rather than signal.
Change-Id: I4a6bbbab6a43bf14a4089e96238a7c8da2c3127e
Reviewed-by: Ulf Hermann <ulf.hermann@qt.io>
In selftests.qrc, imposed alphabetic order (on stem of name, then on
suffix, effectively treating . as sorting before any letter) while
removing old tests and adding new tests and data. Updated all non-csv
files and added many missing files. (Not clear on csv support status;
the script seems to have dropped it after 5.6, but the test still uses
it.)
Left expected_crashes* alone (no new files added, no update to old) as
I don't get results resembling those anticipated.
Omitted printdatatagswithglobaltags, printdatatags due to dangling
hspace on output lines, which upset sanity-bot. A change to the test
cpp is needed to make it viable to skip that dangling hspace.
Change-Id: Iab3fb626c44a91c249b2fb626c12c75ea0317098
Reviewed-by: Frederik Gladhorn <frederik.gladhorn@qt.io>
Some of the subtests are only run with plain-text output format. For
those subtests, the other output formats were unused and gradually
becoming out-of-date.
Change-Id: I4c10f7f5bab2d2cc7d2d2ad641fbf5d4df02b798
Reviewed-by: Rohan McGovern <rohan.mcgovern@nokia.com>
This test was attempting to verify two completely unrelated things, so
this commit splits it into two tests.
Also, printf calls are replaced by qDebug so that the test does not
bypass the testlib loggers.
Change-Id: I1a202af38ce2c69690a32d93405ba604ec6cabee
Reviewed-on: http://codereview.qt-project.org/5178
Reviewed-by: Rohan McGovern <rohan.mcgovern@nokia.com>
