as it's faster, due to one memory scan instead of two
(confirmed by microbenchmark).
Note : as ZSTD_reduceIndex() is rarely invoked,
it does not translate into a visible gain.
Consider it an exercise in auto-vectorization and micro-benchmarking.
It used to stop on reaching extDict, for simplification.
As a consequence, there was a small loss of performance each time the round buffer would restart from beginning.
It's not a large difference though, just several hundreds of bytes on silesia.
This patch fixes it.
This is a pretty nice speed win.
The new strategy consists in stacking new candidates as if it was a hash chain.
Then, only if there is a need to actually consult the chain, they are batch-updated,
before starting the match search itself.
This is supposed to be beneficial when skipping positions,
which happens a lot when using lazy strategy.
The baseline performance for btlazy2 on my laptop is :
15#calgary.tar : 3265536 -> 955985 (3.416), 7.06 MB/s , 618.0 MB/s
15#enwik7 : 10000000 -> 3067341 (3.260), 4.65 MB/s , 521.2 MB/s
15#silesia.tar : 211984896 -> 58095131 (3.649), 6.20 MB/s , 682.4 MB/s
(only level 15 remains for btlazy2, as this strategy is squeezed between lazy2 and btopt)
After this patch, and keeping all parameters identical,
speed is increased by a pretty good margin (+30-50%),
but compression ratio suffers a bit :
15#calgary.tar : 3265536 -> 958060 (3.408), 9.12 MB/s , 621.1 MB/s
15#enwik7 : 10000000 -> 3078318 (3.249), 6.37 MB/s , 525.1 MB/s
15#silesia.tar : 211984896 -> 58444111 (3.627), 9.89 MB/s , 680.4 MB/s
That's because I kept `1<<searchLog` as a maximum number of candidates to update.
But for a hash chain, this represents the total number of candidates in the chain,
while for the binary, it represents the maximum depth of searches.
Keep in mind that a lot of candidates won't even be visited in the btree,
since they are filtered out by the binary sort.
As a consequence, in the new implementation,
the effective depth of the binary tree is substantially shorter.
To compensate, it's enough to increase `searchLog` value.
Here is the result after adding just +1 to searchLog (level 15 setting in this patch):
15#calgary.tar : 3265536 -> 956311 (3.415), 8.32 MB/s , 611.4 MB/s
15#enwik7 : 10000000 -> 3067655 (3.260), 5.43 MB/s , 535.5 MB/s
15#silesia.tar : 211984896 -> 58113144 (3.648), 8.35 MB/s , 679.3 MB/s
aka, almost the same compression ratio as before,
but with a noticeable speed increase (+20-30%).
This modification makes btlazy2 more competitive.
A new round of paramgrill will be necessary to determine which levels are impacted and could adopt the new strategy.
merging of repcode search into btsearch introduced a small compression ratio regressio at max level :
1.3.2 : 52728769
after repMerge patch : 52760789 (+32020)
A few minor changes have produced this difference.
They can be hard to spot.
This patch buys back about half of the difference,
by no longer inserting position at hc3 when a long match is found there.
It feels strangely counter-intuitive, but works :
after this patch : 52742555 (-18234)
ZSTD_updateTree() expected to be followed by a Bt match finder, which would update zc->nextToUpdate.
With the new optimal match finder, it's not necessarily the case : a match might be found during repcode or hash3, and stops there because it reaches sufficient_len, without even entering the binary tree.
Previous policy was to nonetheless update zc->nextToUpdate, but the current position would not be inserted, creating "holes" in the btree, aka positions that will no longer be searched.
Now, when current position is not inserted, zc->nextToUpdate is not update, expecting ZSTD_updateTree() to fill the tree later on.
Solution selected is that ZSTD_updateTree() takes care of properly setting zc->nextToUpdate,
so that it no longer depends on a future function to do this job.
It took time to get there, as the issue started with a memory sanitizer error.
The pb would have been easier to spot with a proper `assert()`.
So this patch add a few of them.
Additionnally, I discovered that `make test` does not enable `assert()` during CLI tests.
This patch enables them.
Unfortunately, these `assert()` triggered other (unrelated) bugs during CLI tests, mostly within zstdmt.
So this patch also fixes them.
- Changed packed structure for gcc memory access : memory sanitizer would complain that a read "might" reach out-of-bound position on the ground that the `union` is larger than the type accessed.
Now, to avoid this issue, each type is independent.
- ZSTD_CCtxParams_setParameter() : @return provides the value of parameter, clamped/fixed appropriately.
- ZSTDMT : changed constant name to ZSTDMT_JOBSIZE_MIN
- ZSTDMT : multithreading is automatically disabled when srcSize <= ZSTDMT_JOBSIZE_MIN, since only one thread will be used in this case (saves memory and runtime).
- ZSTDMT : nbThreads is automatically clamped on setting the value.
