added some test
also updated relevant doc
+ fixed a mistake in `lz4` symlink support :
lz4 utility doesn't remove source files by default (like zstd, but unlike gzip).
The symlink must behave the same.
Produces 3 statistics for ongoing frame compression :
- ingested
- consumed (effectively compressed)
- produced
Ingested can be larger than consumed due to buffering effect.
For the time being, this patch mostly fixes the % ratio issue,
since it computes consumed / produced,
instead of ingested / produced.
That being said, update is not "smooth",
because on a slow enough setting,
fileio spends most of its time waiting for a worker to complete its job.
This could be improved thanks to more granular flushing
i.e. start flushing before ongoing job is fully completed.
this happened on 32-bits build when requiring a too large input buffer,
typically on wlog=29, creating jobs of 2 GB size.
also : zstd32 now compiles with multithread support enabled by default
(can be disabled with HAVE_THREAD=0)
The compression % is no longer correct,
since it's no longer possible to make direct correlation
between nb bytes read and nb bytes written
due to large internal buffer inside CCtx
(exacerbated with --long).
The current "fix" is to no longer display the %.
A more complex solution will have to count exactly how much data has been consumed and compressed internally, within CCtx buffers.
when cli is compiled without MT support,
invoking ZSTD_p_nonBlockingMode result in an error code.
This patch only sets ZSTD_p_nonBlockingMode when ZSTD_MULTITHREAD is set, meaning there is MT support.
The error code could also be intentionnally ignored (there is no side effect).
This new parameter makes it possible to call
streaming ZSTDMT with a single thread set
which is non blocking.
It makes it possible for the main thread to do other tasks in parallel
while the worker thread does compression.
Typically, for zstd cli, it means it can do I/O stuff.
Applied within fileio.c, this patch provides non-negligible gains during compression.
Tested on my laptop, with enwik9 (1000000000 bytes) : time zstd -f enwik9
With traditional single-thread blocking mode :
real 0m9.557s
user 0m8.861s
sys 0m0.538s
With new single-worker non blocking mode :
real 0m7.938s
user 0m8.049s
sys 0m0.514s
=> 20% faster
This fixes the following crash:
$ touch exists
$ programs/zstd -r examples/ -o exists
zstd: exists already exists; not overwritten
Segmentation fault (core dumped)
* programs/fileio.c (FIO_compressMultipleFilenames):
Handle the case where we're not overwriting the destination.
Reported at https://bugzilla.redhat.com/1530049
This patch restores capability for each file to receive adapted compression parameters depending on its size.
The bug breaking this feature was relatively silly :
setting a parameter with a value "0" is supposed to be a no-op.
Unfortunately, it would pin down compression parameters as if they were manually set,
preventing later automatic adaptation.
Unfortunately, I'm currently short of a test case that could check this situation and trigger an error.
Compression parameters selection between tableID 0,1,2,3 is largely internal,
leaving no trace to outside world, not even in frame header.
The new macro might be a bit too restrictive.
Systems which do not support new test will simply default to <time.h>'s `clock_t clock()`,
suffering lesser benchmark accuracy.
Should it matter, the detection macro will have to be upgraded.
There was a flaw in the formula
which compared literal cost with match cost :
at a given position,
a non-null literal suite is going to be part of next sequence,
while if position ends a previous match, to immediately start another match,
next sequence will have a litlength of zero.
A litlength of zero has a non-null cost.
It follows that literals cost should be compared to match cost + litlength==0.
Not doing so gave a structural advantage to matches, which would be selected more often.
I believe that's what led to the creation of the strange heuristic which added a complex cost to matches.
The heuristic was actually compensating.
It was probably created through multiple trials, settling for best outcome on a given scenario (I suspect silesia.tar).
The problem with this heuristic is that it's hard to understand,
and unfortunately, any future change in the parser would impact the way it should be calculated and its effects.
The "proper" formula makes it possible to remove this heuristic.
Now, the problem is : in a head to head comparison, it's sometimes better, sometimes worse.
Note that all differences are small (< 0.01 ratio).
In general, the newer formula is better for smaller files (for example, calgary.tar and enwik7).
I suspect that's because starting statistics are pretty poor (another area of improvement).
However, for silesia.tar specifically, it's worse at level 22 (while being better at level 17, so even compression level has an impact ...).
It's a pity that zstd -22 gets worse on silesia.tar.
That being said, I like that the new code gets rid of strange variables,
which were introducing complexity for any future evolution (faster variants being in mind).
Therefore, in spite of this detrimental side effect, I tend to be in favor of it.
Fixes issue where, when `zstd --format=lz4` is fed an input larger than 128KB,
the read overruns the input buffer. This changes Zstd to use LZ4 with chained
64KB blocks. This is technically a breaking change in that some third party
LZ4 implementations may not support linked blocks. However, progress should not
be allowed to be stopped by such petty concerns as backwards compatibility!
adapt accuracy depending on value.
makes it possible to have higher accuracy for small value,
notably small compression speed.
This capability is expected to be useful while modifying optimal parser.
Currently, all files are joined by default,
they are compressed separately but benchmarked together,
providing a single final result.
Benchmarking files separately make it possible to accurately measure difference for each file.
This is expected to be useful while tuning optimal parser.
this version has same speed as branch `opt`
which is itself 5-10% slower than branch `dev`
(no identified reason)
It does not compress exactly the same as `opt` or `dev`,
maybe because it doesn't stop search after repcodes,
leading to sometimes better compression, sometimes worse
(by a small margin).
warning : _extDict path does not work for the time being
This means that benchmark module works,
but file module will fail with large files (and high compression level).
Objective is to fuse _extDict path into current one,
in order to have a single parser to maintain.
as per documentation, on ZSTD_setPledgedSrcSize() :
> If all data is provided and consumed in a single round,
> this value (pledgedSrcSize) is overriden by srcSize instead.
This wasn't applied before compression level is transformed into compression parameters.
As a consequence, small input missed compression parameters adaptation.
It seems to work fine now : compression was compared with ZSTD_compress_advanced(),
results were the same.
