PTHREAD_MUTEX_NORMAL requires deadlock for nesting, DEFAULT
does not. Since glibc uses the same value (0) disable elision
for any call to pthread_mutexattr_settype() with a 0 value.
This implies that a program can disable elision by doing
pthread_mutexattr_settype(&attr, PTHREAD_MUTEX_NORMAL)
Based on a original proposal by Rich Felker.
Add elision paths to the basic mutex locks.
The normal path has a check for RTM and upgrades the lock
to RTM when available. Trylocks cannot automatically upgrade,
so they check for elision every time.
We use a 4 byte value in the mutex to store the lock
elision adaptation state. This is separate from the adaptive
spin state and uses a separate field.
Condition variables currently do not support elision.
Recursive mutexes and condition variables may be supported at some point,
but are not in the current implementation. Also "trylock" will
not automatically enable elision unless some other lock call
has been already called on the lock.
This version does not use IFUNC, so it means every lock has one
additional check for elision. Benchmarking showed the overhead
to be negligible.
tst-mutex5 and 8 test some behaviour not required by POSIX,
that elision changes. This changes these tests to not check
this when elision is enabled at configure time.
Add Enable/disable flags used internally
Extend the mutex initializers to have the fields needed for
elision. The layout stays the same, and this is not visible
to programs.
These changes are not exposed outside pthread
Lock elision using TSX is a technique to optimize lock scaling
It allows to run locks in parallel using hardware support for
a transactional execution mode in 4th generation Intel Core CPUs.
See http://www.intel.com/software/tsx for more Information.
This patch implements a simple adaptive lock elision algorithm based
on RTM. It enables elision for the pthread mutexes and rwlocks.
The algorithm keeps track whether a mutex successfully elides or not,
and stops eliding for some time when it is not.
When the CPU supports RTM the elision path is automatically tried,
otherwise any elision is disabled.
The adaptation algorithm and its tuning is currently preliminary.
The code adds some checks to the lock fast paths. Micro-benchmarks
show little to no difference without RTM.
This patch implements the low level "lll_" code for lock elision.
Followon patches hook this into the pthread implementation
Changes with the RTM mutexes:
-----------------------------
Lock elision in pthreads is generally compatible with existing programs.
There are some obscure exceptions, which are expected to be uncommon.
See the manual for more details.
- A broken program that unlocks a free lock will crash.
There are ways around this with some tradeoffs (more code in hot paths)
I'm still undecided on what approach to take here; have to wait for testing reports.
- pthread_mutex_destroy of a lock mutex will not return EBUSY but 0.
- There's also a similar situation with trylock outside the mutex,
"knowing" that the mutex must be held due to some other condition.
In this case an assert failure cannot be recovered. This situation is
usually an existing bug in the program.
- Same applies to the rwlocks. Some of the return values changes
(for example there is no EDEADLK for an elided lock, unless it aborts.
However when elided it will also never deadlock of course)
- Timing changes, so broken programs that make assumptions about specific timing
may expose already existing latent problems. Note that these broken programs will
break in other situations too (loaded system, new faster hardware, compiler
optimizations etc.)
- Programs with non recursive mutexes that take them recursively in a thread and
which would always deadlock without elision may not always see a deadlock.
The deadlock will only happen on an early or delayed abort (which typically
happens at some point)
This only happens for mutexes not explicitely set to PTHREAD_MUTEX_NORMAL
or PTHREAD_MUTEX_ADAPTIVE_NP. PTHREAD_MUTEX_NORMAL mutexes do not elide.
The elision default can be set at configure time.
This patch implements the basic infrastructure for elision.
This change creates a link map in static executables to serve as the
global search list for dlopen. It fixes a problem with the inability
to access the global symbol object and a crash on an attempt to map a
DSO into the global scope. Some code that has become dead after the
addition of this link map is removed too and test cases are provided.
This function is now called from dl_open_worker with the GL(dl_load_lock)
lock held and no longer needs local protection. GL(dl_load_lock) also
correctly protects _dl_lookup_symbol_x called here that relies on the
caller to have serialized access to the data structures it uses.
Many Linux arches require fixed mmaps to be aligned higher than pagesize,
so use the SHMLBA define as it represents this quantity exactly.
This fixes spurious errors seen on those arches like:
cannot map archive header: Invalid argument
URL: http://sourceware.org/bugzilla/show_bug.cgi?id=10283
Reported-by: CHIKAMA Masaki <masaki.chikama@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Rather than open coding the masks, add helper macros to do the magic.
This makes code easier to read.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Static applications that call pthread_exit on the main
thread segfault. This is because after a thread terminates
__libc_start_main decrements __nptl_nthreads which is only
defined in pthread_create. Therefore the right solution is
to add a requirement to pthread_create from pthread_exit.
~~~
nptl/
2013-06-24 Vladimir Nikulichev <v.nikulichev@gmail.com>
[BZ #12310]
* pthread_exit.c: Add reference to pthread_create.
