Pathological samples may result in literal section being incompressible.
This case is now detected,
and literal distribution is replaced by one that can be written into the dictionary.
The deep fuzzer tests caught a subtle bug that was probably there for a long time.
The impact of the bug is not a crash, or any other clear error signal,
rather, it reduces performance, by cutting data into smaller blocks.
Eventually, the following test would fail because it produces too many 1-byte blocks,
requiring more space than buffer can provide :
`./zstreamtest_asan --mt -s3514 -t1678312 -i1678314`
The root scenario is as follows :
- Create context, initialize it using explicit parameters or a `cdict` to pin them down, set `pledgedSrcSize=1`
- The compression parameters will not be adapted, but `windowSize` and `blockSize` will be automatically set to `1`.
`windowSize` and `blockSize` are dynamic values, set within `ZSTD_resetCCtx_internal()`.
The automatic adaptation makes it possible to generate smaller contexts for smaller input sizes.
- Complete compression
- New compression with same context, using same parameters, but `pledgedSrcSize=ZSTD_CONTENTSIZE_UNKNOWN`
trigger "continue mode"
- Continue mode doesn't modify blockSize, because it used to depend on `windowLog` only,
but in fact, it also depends on `pledgedSrcSize`.
- The "old" blocksize (1) is still there,
next compression will use this value to cut input into blocks,
resulting in more blocks and worse performance than necessary performance.
Given the scenario, and its possible variants, I'm surprised it did not show up before.
But I suspect it did show up, it's just that it never triggered an error, because "worse performance" is not a trigger.
The above test is a special corner case, where performance is so impacted that it reaches an error case.
The fix works, but I'm not completely pleased.
I think the current code relies too much on implied relations between variables.
This will likely break again in the future when some related part of the code change.
Unfortunately, no time to make larger changes if we want to keep the release target for zstd v1.3.3.
So a longer term fix will have to be considered after the release.
To do : create a reliable test case which triggers this scenario for CI tests.
There was a flaw in the formula
which compared literal cost with match cost :
at a given position,
a non-null literal suite is going to be part of next sequence,
while if position ends a previous match, to immediately start another match,
next sequence will have a litlength of zero.
A litlength of zero has a non-null cost.
It follows that literals cost should be compared to match cost + litlength==0.
Not doing so gave a structural advantage to matches, which would be selected more often.
I believe that's what led to the creation of the strange heuristic which added a complex cost to matches.
The heuristic was actually compensating.
It was probably created through multiple trials, settling for best outcome on a given scenario (I suspect silesia.tar).
The problem with this heuristic is that it's hard to understand,
and unfortunately, any future change in the parser would impact the way it should be calculated and its effects.
The "proper" formula makes it possible to remove this heuristic.
Now, the problem is : in a head to head comparison, it's sometimes better, sometimes worse.
Note that all differences are small (< 0.01 ratio).
In general, the newer formula is better for smaller files (for example, calgary.tar and enwik7).
I suspect that's because starting statistics are pretty poor (another area of improvement).
However, for silesia.tar specifically, it's worse at level 22 (while being better at level 17, so even compression level has an impact ...).
It's a pity that zstd -22 gets worse on silesia.tar.
That being said, I like that the new code gets rid of strange variables,
which were introducing complexity for any future evolution (faster variants being in mind).
Therefore, in spite of this detrimental side effect, I tend to be in favor of it.
ZSTD_updateTree() expected to be followed by a Bt match finder, which would update zc->nextToUpdate.
With the new optimal match finder, it's not necessarily the case : a match might be found during repcode or hash3, and stops there because it reaches sufficient_len, without even entering the binary tree.
Previous policy was to nonetheless update zc->nextToUpdate, but the current position would not be inserted, creating "holes" in the btree, aka positions that will no longer be searched.
Now, when current position is not inserted, zc->nextToUpdate is not update, expecting ZSTD_updateTree() to fill the tree later on.
Solution selected is that ZSTD_updateTree() takes care of properly setting zc->nextToUpdate,
so that it no longer depends on a future function to do this job.
It took time to get there, as the issue started with a memory sanitizer error.
The pb would have been easier to spot with a proper `assert()`.
So this patch add a few of them.
Additionnally, I discovered that `make test` does not enable `assert()` during CLI tests.
This patch enables them.
Unfortunately, these `assert()` triggered other (unrelated) bugs during CLI tests, mostly within zstdmt.
So this patch also fixes them.
- Changed packed structure for gcc memory access : memory sanitizer would complain that a read "might" reach out-of-bound position on the ground that the `union` is larger than the type accessed.
Now, to avoid this issue, each type is independent.
- ZSTD_CCtxParams_setParameter() : @return provides the value of parameter, clamped/fixed appropriately.
- ZSTDMT : changed constant name to ZSTDMT_JOBSIZE_MIN
- ZSTDMT : multithreading is automatically disabled when srcSize <= ZSTDMT_JOBSIZE_MIN, since only one thread will be used in this case (saves memory and runtime).
- ZSTDMT : nbThreads is automatically clamped on setting the value.
this version has same speed as branch `opt`
which is itself 5-10% slower than branch `dev`
(no identified reason)
It does not compress exactly the same as `opt` or `dev`,
maybe because it doesn't stop search after repcodes,
leading to sometimes better compression, sometimes worse
(by a small margin).
warning : _extDict path does not work for the time being
This means that benchmark module works,
but file module will fail with large files (and high compression level).
Objective is to fuse _extDict path into current one,
in order to have a single parser to maintain.
* Maximum window size in 32-bit mode is 1GB, since allocations for 2GB fail
on my Mac.
* Maximum window size in 64-bit mode is 2GB, since that is the largest
power of 2 that works with the overflow prevention.
* Allow `--long=windowLog` to set the window log, along with
`--zstd=wlog=#`. These options also set the window size during
decompression, but don't override `--memory=#` if it is set.
* Present a helpful error message when the window size is too large during
decompression.
* The long range matcher defaults to a hash log 7 less than the window log,
which keeps it at 20 for window log 27.
* Keep the default long range matcher window size and the default maximum
window size at 27 for the API and CLI.
* Add tests that use the maximum window size and hash size for compression
and decompression.
