This was straightforward to implement in GLSL. The
`ShadingRateInterlockOrderedEXT` and `ShadingRateInterlockUnorderedEXT`
modes aren't implemented yet, because we don't support
`SPV_NV_shading_rate` or `SPV_EXT_fragment_invocation_density` yet.
HLSL and MSL were more interesting. They don't support this directly,
but they do support marking resources as "rasterizer ordered," which
does roughly the same thing. So this implementation scans all accesses
inside the critical section and marks all storage resources found
therein as rasterizer ordered. They also don't support the fine-grained
controls on pixel- vs. sample-level interlock and disabling ordering
guarantees that GLSL and SPIR-V do, but that's OK. "Unordered" here
merely means the order is undefined; that it just so happens to be the
same as rasterizer order is immaterial. As for pixel- vs. sample-level
interlock, Vulkan explicitly states:
> With sample shading enabled, [the `PixelInterlockOrderedEXT` and
> `PixelInterlockUnorderedEXT`] execution modes are treated like
> `SampleInterlockOrderedEXT` or `SampleInterlockUnorderedEXT`
> respectively.
and:
> If [the `SampleInterlockOrderedEXT` or `SampleInterlockUnorderedEXT`]
> execution modes are used in single-sample mode they are treated like
> `PixelInterlockOrderedEXT` or `PixelInterlockUnorderedEXT`
> respectively.
So this will DTRT for MoltenVK and gfx-rs, at least.
MSL additionally supports multiple raster order groups; resources that
are not accessed together can be placed in different ROGs to allow them
to be synchronized separately. A more sophisticated analysis might be
able to place resources optimally, but that's outside the scope of this
change. For now, we assign all resources to group 0, which should do for
our purposes.
`glslang` doesn't support the `RasterizerOrdered` UAVs this
implementation produces for HLSL, so the test case needs `fxc.exe`.
It also insists on GLSL 4.50 for `GL_ARB_fragment_shader_interlock`,
even though the spec says it needs either 4.20 or
`GL_ARB_shader_image_load_store`; and it doesn't support the
`GL_NV_fragment_shader_interlock` extension at all. So I haven't been
able to test those code paths.
Fixes#1002.
This extension provides a new operation which causes a fragment to be
discarded without terminating the fragment shader invocation. The
invocation for the discarded fragment becomes a helper invocation, so
that derivatives will remain defined. The old `HelperInvocation` builtin
becomes undefined when this occurs, so a second new instruction queries
the current helper invocation status.
This is only fully supported for GLSL. HLSL doesn't support the
`IsHelperInvocation` operation and MSL doesn't support the
`DemoteToHelperInvocation` op.
Fixes#1052.
Fix fallout from changes.
There's a bug in glslang that prevents `float16_t`, `[u]int16_t`, and
`[u]int8_t` constants from adding the corresponding SPIR-V capabilities.
SPIRV-Tools, meanwhile, tightened validation so that these constants are
only valid if the corresponding `Float16`, `Int16`, and `Int8` caps are
on. This affects the `16bit-constants.frag` test for GLSL and MSL.
There is a case where we can deduce a for/while loop, but the continue
block is actually very painful to deal with, so handle that case as
well. Removes an exceptional case.
MSL does not seem to have a qualifier for this, but HLSL SM 5.1 does.
glslangValidator for HLSL does not support this, so skip any validation,
but it passes in FXC.
This is required to avoid relying on complex sub-expression elimination
in compilers, and generates cleaner code.
The problem case is if a complex expression is used in an access chain,
like:
Composite comp = buffer[texture(...)];
vec4 a = comp.a + comp.b + comp.c;
Before, we did not have common subexpression tracking for
OpLoad/OpAccessChain, so we easily ended up with code like:
vec4 a = buffer[texture(...)].a + buffer[texture(...)].b + buffer[texture(...)].c;
A good compiler will optimize this, but we should not rely on it, and
forcing texture(...) to a temporary also looks better.
The solution is to add a vector "implied_expression_reads", which works
similarly to expression_dependencies. We also need an extra mechanism in
to_expression which lets us skip expression read checking and do it
later. E.g. for expr -> access chain -> load, we should only trigger
a read of expr when using the loaded expression.
- Add new Windows support
- Use CMake/CTest instead of Make + shell scripts
- Use --parallel in CTest
- Fix CTest on Windows
- Cleanups in test_shaders.py
- Force specific commit for SPIRV-Headers
- Fix Inf/NaN odd-ball case by moving to ASM
HLSL just picked the variable name which did not work as expected for
some users. Use the same logic as GLSL and set up declared_block_names,
so the actual name can be queried later.
A lot of changes in spirv-opt output.
Some new invalid SPIR-V was found but most of them were not significant
for SPIRV-Cross, so just marked them as invalid.
