To facilitate an improved linking-by-name use case for older GL,
we will be more aggressive about merging struct definitions, even for
rather unrelated cases where we don't strictly need to use type aliases.
This CL updates the test runner to only run spirv-opt if the generated
SPIR-V is valid. If validation is skipped it's possible to hit aborts
and other memory errors in the optimizer as it assumes the SPIR-V is
valid.
Rolled the hashes used for glslang, SPIRV-Tools, and SPIRV-Headers to
HEAD, which includes the update to 1.5.
Added passing '--amb' to glslang, so I didn't have to explicitly set
bindings in a large number of test shaders that currently don't, and
now glslang considers them invalid.
Marked all shaders that no longer pass spirv-val as .invalid.
This was straightforward to implement in GLSL. The
`ShadingRateInterlockOrderedEXT` and `ShadingRateInterlockUnorderedEXT`
modes aren't implemented yet, because we don't support
`SPV_NV_shading_rate` or `SPV_EXT_fragment_invocation_density` yet.
HLSL and MSL were more interesting. They don't support this directly,
but they do support marking resources as "rasterizer ordered," which
does roughly the same thing. So this implementation scans all accesses
inside the critical section and marks all storage resources found
therein as rasterizer ordered. They also don't support the fine-grained
controls on pixel- vs. sample-level interlock and disabling ordering
guarantees that GLSL and SPIR-V do, but that's OK. "Unordered" here
merely means the order is undefined; that it just so happens to be the
same as rasterizer order is immaterial. As for pixel- vs. sample-level
interlock, Vulkan explicitly states:
> With sample shading enabled, [the `PixelInterlockOrderedEXT` and
> `PixelInterlockUnorderedEXT`] execution modes are treated like
> `SampleInterlockOrderedEXT` or `SampleInterlockUnorderedEXT`
> respectively.
and:
> If [the `SampleInterlockOrderedEXT` or `SampleInterlockUnorderedEXT`]
> execution modes are used in single-sample mode they are treated like
> `PixelInterlockOrderedEXT` or `PixelInterlockUnorderedEXT`
> respectively.
So this will DTRT for MoltenVK and gfx-rs, at least.
MSL additionally supports multiple raster order groups; resources that
are not accessed together can be placed in different ROGs to allow them
to be synchronized separately. A more sophisticated analysis might be
able to place resources optimally, but that's outside the scope of this
change. For now, we assign all resources to group 0, which should do for
our purposes.
`glslang` doesn't support the `RasterizerOrdered` UAVs this
implementation produces for HLSL, so the test case needs `fxc.exe`.
It also insists on GLSL 4.50 for `GL_ARB_fragment_shader_interlock`,
even though the spec says it needs either 4.20 or
`GL_ARB_shader_image_load_store`; and it doesn't support the
`GL_NV_fragment_shader_interlock` extension at all. So I haven't been
able to test those code paths.
Fixes#1002.
This subtle bug removed any expression validation for trivially swizzled
variables. Make usage suppression a more explicit concept rather than
just hacking off forwarded_temporaries.
There is some fallout here with loop generation since our expression
invalidation is currently a bit too naive to handle loops properly.
The forwarding bug masked this problem until now.
If part of the loop condition is also used in the body, we end up
reading an invalid expression, which in turn forces a temporary to be
generated in the condition block, not good. We'll need to be smarter
here ...
This extension provides a new operation which causes a fragment to be
discarded without terminating the fragment shader invocation. The
invocation for the discarded fragment becomes a helper invocation, so
that derivatives will remain defined. The old `HelperInvocation` builtin
becomes undefined when this occurs, so a second new instruction queries
the current helper invocation status.
This is only fully supported for GLSL. HLSL doesn't support the
`IsHelperInvocation` operation and MSL doesn't support the
`DemoteToHelperInvocation` op.
Fixes#1052.
Fix fallout from changes.
There's a bug in glslang that prevents `float16_t`, `[u]int16_t`, and
`[u]int8_t` constants from adding the corresponding SPIR-V capabilities.
SPIRV-Tools, meanwhile, tightened validation so that these constants are
only valid if the corresponding `Float16`, `Int16`, and `Int8` caps are
on. This affects the `16bit-constants.frag` test for GLSL and MSL.
There is a case where we can deduce a for/while loop, but the continue
block is actually very painful to deal with, so handle that case as
well. Removes an exceptional case.
MSL does not seem to have a qualifier for this, but HLSL SM 5.1 does.
glslangValidator for HLSL does not support this, so skip any validation,
but it passes in FXC.
This is a fairly fundamental change on how IDs are handled.
It serves many purposes:
- Improve performance. We only need to iterate over IDs which are
relevant at any one time.
- Makes sure we iterate through IDs in SPIR-V module declaration order
rather than ID space. IDs don't have to be monotonically increasing,
which was an assumption SPIRV-Cross used to have. It has apparently
never been a problem until now.
- Support LUTs of structs. We do this by interleaving declaration of
constants and struct types in SPIR-V module order.
To support this, the ParsedIR interface needed to change slightly.
Before setting any ID with variant_set<T> we let ParsedIR know
that an ID with a specific type has been added. The surface for change
should be minimal.
ParsedIR will maintain a per-type list of IDs which the cross-compiler
will need to consider for later.
Instead of looping over ir.ids[] (which can be extremely large), we loop
over types now, using:
ir.for_each_typed_id<SPIRVariable>([&](uint32_t id, SPIRVariable &var) {
handle_variable(var);
});
Now we make sure that we're never looking at irrelevant types.
A block name cannot alias with any name in its own scope,
and it cannot alias with any other "global" name.
To solve this, we need to complicate the name cache updates a little bit
where we have a "primary" namespace and "secondary" namespace.
