Continuing fixes for ceil, floor and trunc functions not to raise the
"inexact" exception, this patch fixes the versions used on older
powerpc32 processors. As was done with the round implementations some
time ago, the save of floating-point state is moved after the first
floating-point operation on the input to ensure that any "invalid"
exception from signaling NaN input is included in the saved state, and
then the whole state gets restored rather than just the rounding mode.
This has no effect on configurations using the power5+ code, since
such processors can do these operations with a single instruction (and
those instructions do not set "inexact", so are correct for TS 18661-1
semantics).
Tested for powerpc32.
[BZ #15479]
* sysdeps/powerpc/powerpc32/fpu/s_ceil.S (__ceil): Move save of
floating-point state after first floating-point operation on
input. Restore full floating-point state instead of just rounding
mode.
* sysdeps/powerpc/powerpc32/fpu/s_ceilf.S (__ceilf): Likewise.
* sysdeps/powerpc/powerpc32/fpu/s_floor.S (__floor): Likewise.
* sysdeps/powerpc/powerpc32/fpu/s_floorf.S (__floorf): Likewise.
* sysdeps/powerpc/powerpc32/fpu/s_trunc.S (__trunc): Likewise.
* sysdeps/powerpc/powerpc32/fpu/s_truncf.S (__truncf): Likewise.
According to the latest Unicode standard, a conversion from/to UTF-xx has
to report an error if the character value is in range of an utf16 surrogate
(0xd800..0xdfff). See https://sourceware.org/ml/libc-help/2015-12/msg00015.html.
Thus this patch fixes this behaviour for converting from utf32 to internal and
from internal to utf8.
Furthermore the conversion from utf16 to internal does not report an error if the
input-stream consists of two low-surrogate values. If an uint16_t value is in the
range of 0xd800 .. 0xdfff, the next uint16_t value is checked, if it is in the
range of a low surrogate (0xdc00 .. 0xdfff). Afterwards these two uint16_t
values are interpreted as a high- and low-surrogates pair. But there is no test
if the first uint16_t value is really in the range of a high-surrogate
(0xd800 .. 0xdbff). If there would be two uint16_t values in the range of a low
surrogate, then they will be treated as a valid high- and low-surrogates pair.
This patch adds this test.
This patch also adds a new testcase, which checks UTF conversions with input
values in range of UTF16 surrogates. The test converts from UTF-xx to INTERNAL,
INTERNAL to UTF-xx and directly between UTF-xx to UTF-yy. The latter conversion
is needed because s390 has iconv-modules, which converts from/to UTF in one step.
The new testcase was tested on a s390, power and intel machine.
ChangeLog:
[BZ #19727]
* iconvdata/utf-16.c (BODY): Report an error if first word is not a
valid high surrogate.
* iconvdata/utf-32.c (BODY): Report an error if the value is in range
of an utf16 surrogate.
* iconv/gconv_simple.c (BODY): Likewise.
* iconvdata/bug-iconv12.c: New file.
* iconvdata/Makefile (tests): Add bug-iconv12.
rename test
When converting from UCS4LE to INTERNAL, the input-value is checked for a too
large value and the iconv() call sets errno to EILSEQ. In this case the inbuf
argument of the iconv() call should point to the invalid character, but it
points to the beginning of the inbuf.
Thus this patch updates the pointers inptrp and outptrp before returning in
this error case.
This patch also adds a new testcase for this issue.
The new test was tested on a s390, power, intel machine.
ChangeLog:
[BZ #19726]
* iconv/gconv_simple.c (ucs4le_internal_loop): Update inptrp and
outptrp in case of an illegal input.
* iconv/tst-iconv6.c: New file.
* iconv/Makefile (tests): Add tst-iconv6.
According to the latest Unicode standard, a conversion from/to UTF-xx has
to report an error if the character value is in range of an utf16 surrogate
(0xd800..0xdfff). See https://sourceware.org/ml/libc-help/2015-12/msg00015.html.
Thus the cu42 instruction, which converts from utf32 to utf16, has to be
disabled because it does not report an error in case of a value in range of
a low surrogate (0xdc00..0xdfff). The etf3eh variant is removed and the c,
vector variant is adjusted to handle the value in range of an utf16 low
surrogate correctly.
ChangeLog:
* sysdeps/s390/utf16-utf32-z9.c: Disable cu42 instruction and report
an error in case of a value in range of an utf16 low surrogate.
According to the latest Unicode standard, a conversion from/to UTF-xx has
to report an error if the character value is in range of an utf16 surrogate
(0xd800..0xdfff). See https://sourceware.org/ml/libc-help/2015-12/msg00015.html.
Thus the cu41 instruction, which converts from utf32 to utf8, has to be
disabled because it does not report an error in case of a value in range of
a low surrogate (0xdc00..0xdfff). The etf3eh variant is removed and the c,
vector variant is adjusted to handle the value in range of an utf16 low
surrogate correctly.
ChangeLog:
* sysdeps/s390/utf8-utf32-z9.c: Disable cu41 instruction and report
an error in case of a value in range of an utf16 low surrogate.
This patch reworks the existing s390 64bit specific iconv modules in order
to use them on s390 31bit, too.
Thus the parts for subdirectory iconvdata in sysdeps/s390/s390-64/Makefile
were moved to sysdeps/s390/Makefile so that they apply on 31bit, too.
All those modules are moved from sysdeps/s390/s390-64 directory to sysdeps/s390.
The iso-8859-1 to/from cp037 module was adjusted, to use brct (branch relative
on count) instruction on 31bit s390 instead of brctg, because the brctg is a
zarch instruction and is not available on a 31bit kernel.
The utf modules are using zarch instructions, thus the directive machinemode
zarch_nohighgprs was added to the inline assemblies to omit the high-gprs flag
in the shared libraries. Otherwise they can't be loaded on a 31bit kernel.
The ifunc resolvers were adjusted in order to call the etf3eh or vector variants
only if zarch instructions are available (64bit kernel in 31bit compat-mode).
Furthermore some variable types were changed. E.g. unsigned long long would be
a register pair on s390 31bit, but we want only one single register.
For variables of type size_t the register contents have to be enlarged from a
32bit to a 64bit value on 31bit, because the inline assemblies uses 64bit values
in such cases.
ChangeLog:
* sysdeps/s390/s390-64/Makefile (iconvdata-subdirectory):
Move to ...
* sysdeps/s390/Makefile: ... here.
* sysdeps/s390/s390-64/iso-8859-1_cp037_z900.c: Move to ...
* sysdeps/s390/iso-8859-1_cp037_z900.c: ... here.
(BRANCH_ON_COUNT): New define.
(TR_LOOP): Use BRANCH_ON_COUNT instead of brctg.
* sysdeps/s390/s390-64/utf16-utf32-z9.c: Move to ...
* sysdeps/s390/utf16-utf32-z9.c: ... here and adjust to
run on s390-32, too.
* sysdeps/s390/s390-64/utf8-utf16-z9.c: Move to ...
* sysdeps/s390/utf8-utf16-z9.c: ... here and adjust to
run on s390-32, too.
* sysdeps/s390/s390-64/utf8-utf32-z9.c: Move to ...
* sysdeps/s390/utf8-utf32-z9.c: ... here and adjust to
run on s390-32, too.
This patch reworks the s390 specific module to convert between utf16 and utf32.
Now ifunc is used to choose either the c or etf3eh (with convert utf
instruction) variants at runtime.
Furthermore a new vector variant for z13 is introduced which will be build
and chosen if vector support is available at build / runtime.
In case of converting utf 32 to utf16, the vector variant optimizes input of
2byte utf16 characters. The convert utf instruction is used if an utf16
surrogate is found.
For the other direction utf16 to utf32, the cu24 instruction can't be re-
enabled, because it does not report an error, if the input-stream consists of
a single low surrogate utf16 char (e.g. 0xdc00). This applies to the newest z13,
too. Thus there is only the c or the new vector variant, which can handle utf16
surrogate characters.
This patch also fixes some whitespace errors. Furthermore, the etf3eh variant is
handling the "UTF-xx//IGNORE" case now. Before they ignored the ignore-case and
always stopped at an error.
ChangeLog:
* sysdeps/s390/s390-64/utf16-utf32-z9.c: Use ifunc to select c,
etf3eh or new vector loop-variant.
This patch reworks the s390 specific module to convert between utf8 and utf16.
Now ifunc is used to choose either the c or etf3eh (with convert utf instruction)
variants at runtime. Furthermore a new vector variant for z13 is introduced
which will be build and chosen if vector support is available at build / runtime.
In case of converting utf 8 to utf16, the vector variant optimizes input of
1byte utf8 characters. The convert utf instruction is used if a multibyte utf8
character is found.
For the other direction utf16 to utf8, the cu21 instruction can't be re-enabled,
because it does not report an error, if the input-stream consists of a single
low surrogate utf16 char (e.g. 0xdc00). This applies to the newest z13, too.
Thus there is only the c or the new vector variant, which can handle 1..4 byte
utf8 characters.
The c variant from utf16 to utf8 has beed fixed. If a high surrogate was at the
end of the input-buffer, then errno was set to EINVAL and the input-pointer
pointed just after the high surrogate. Now it points to the beginning of the
high surrogate.
This patch also fixes some whitespace errors. The c variant from utf8 to utf16
is now checking that tail-bytes starts with 0b10... and the value is not in
range of an utf16 surrogate.
Furthermore, the etf3eh variants are handling the "UTF-xx//IGNORE" case now.
Before they ignored the ignore-case and always stopped at an error.
ChangeLog:
* sysdeps/s390/s390-64/utf8-utf16-z9.c: Use ifunc to select c,
etf3eh or new vector loop-variant.
This patch reworks the s390 specific module to convert between utf8 and utf32.
Now ifunc is used to choose either the c or etf3eh (with convert utf
instruction) variants at runtime.
Furthermore a new vector variant for z13 is introduced which will be build
and chosen if vector support is available at build / runtime.
The vector variants optimize input of 1byte utf8 characters. The convert utf
instruction is used if a multibyte utf8 character is found.
This patch also fixes some whitespace errors. The c variants are rejecting
UTF-16 surrogates and values above 0x10ffff now.
Furthermore, the etf3eh variants are handling the "UTF-xx//IGNORE" case now.
Before they ignored the ignore-case and always stopped at an error.
ChangeLog:
* sysdeps/s390/s390-64/utf8-utf32-z9.c: Use ifunc to select c, etf3eh
or new vector loop-variant.
This patch reworks the s390 specific module which used the z900
translate one to one instruction. Now the g5 translate instruction is used,
because it outperforms the troo instruction.
ChangeLog:
* sysdeps/s390/s390-64/iso-8859-1_cp037_z900.c (TROO_LOOP):
Rename to TR_LOOP and usage of tr instead of troo instruction.
This patch introduces a s390 specific gconv_simple.c file which provides
optimized versions for z13 with vector instructions, which will be chosen at
runtime via ifunc.
The optimized conversions can convert between internal and ascii, ucs4, ucs4le,
ucs2, ucs2le.
If the build-environment lacks vector support, then iconv/gconv_simple.c
is used wihtout any change. Otherwise iconvdata/gconv_simple.c is used to create
conversion loop routines without vector instructions as fallback, if vector
instructions aren't available at runtime.
ChangeLog:
* sysdeps/s390/multiarch/gconv_simple.c: New File.
* sysdeps/s390/multiarch/Makefile (sysdep_routines): Add gconv_simple.
This patch introduces a s390 specific 8bit-generic.c file which provides an
optimized version for z13 with translate-/vector-instructions, which will be
chosen at runtime via ifunc.
If the build-environment lacks vector support, then iconvdata/8bit-generic.c
is used wihtout any change. Otherwise iconvdata/8bit-generic.c is used to create
conversion loop routines without vector instructions as fallback, if vector
instructions aren't available at runtime.
The vector routines can only be used with charsets where the maximum UCS4 value
fits in 1 byte size. Then the hardware translate-instruction is used
to translate between up to 256 generic characters and "1 byte UCS4"
characters at once. The vector instructions are used to convert between
the "1 byte UCS4" and UCS4.
The gen-8bit.sh script in sysdeps/s390/multiarch generates the conversion
table to_ucs1. Therefore in sysdeps/s390/multiarch/Makefile is added an
override define generate-8bit-table, which is originally defined in
iconvdata/Makefile. This version calls the gen-8bit.sh in iconvdata folder
and the s390 one.
ChangeLog:
* sysdeps/s390/multiarch/8bit-generic.c: New File.
* sysdeps/s390/multiarch/gen-8bit.sh: New File.
* sysdeps/s390/multiarch/Makefile (generate-8bit-table):
New override define.
* sysdeps/s390/multiarch/iconv/skeleton.c: Likewise.
The S390 specific test checks if the gcc has support for vector registers
by compiling an inline assembly which clobbers vector registers.
On success the macro HAVE_S390_VX_GCC_SUPPORT is defined.
This macro can be used to determine if e.g. clobbering vector registers
is allowed or not.
ChangeLog:
* config.h.in (HAVE_S390_VX_GCC_SUPPORT): New macro undefine.
* sysdeps/s390/configure.ac: Add test for S390 vector register
support in gcc.
* sysdeps/s390/configure: Regenerated.
This patch introduces a way to provide an architecture dependent gconv-modules
file. Before this patch, the gconv-modules file was normally installed from
src-dir/iconvdata/gconv-modules. The S390 Makefile had overridden the
installation recipe (with a make warning) in order to install the
gconv-module-s390 file from build-dir.
The iconvdata/Makefile provides another recipe, which copies the gconv-modules
file from src to build dir, which are used by the testcases.
Thus the testcases does not use the currently build s390-modules.
This patch uses build-dir/iconvdata/gconv-modules for installation, which
is generated by concatenating src-dir/iconvdata/gconv-modules and the
architecture specific one. The latter one can be specified by setting the variable
sysdeps-gconv-modules in sysdeps/.../Makefile.
The architecture specific gconv-modules file is emitted before the common one
because these modules aren't used in all possible conversions. E.g. the converting
from INTERNAL to UTF-16 used the common UTF-16.so module instead of UTF16_UTF32_Z9.so.
This way, the s390-Makefile does not need to override the recipe for gconv-modules
and no warning is emitted anymore.
Since we no longer support empty objpfx the conditional test in iconvdata/Makefile
is removed.
ChangeLog:
* iconvdata/Makefile ($(inst_gconvdir)/gconv-modules):
Install file from $(objpfx)gconv-modules.
($(objpfx)gconv-modules): Concatenate architecture specific file
in variable sysdeps-gconv-modules and gconv-modules in src dir.
* sysdeps/s390/gconv-modules: New file.
* sysdeps/s390/s390-64/Makefile: ($(inst_gconvdir)/gconv-modules):
Deleted.
($(objpfx)gconv-modules-s390): Deleted.
(sysdeps-gconv-modules): New variable.
Continuing fixes for ceil and floor functions not to raise the
"inexact" exception, this patch fixes the x86_64 SSE4.1 versions. The
roundss / roundsd instructions take an immediate operand that
determines the rounding mode and whether to raise "inexact"; this just
needs bit 3 set to disable "inexact", which this patch does.
Remark: we don't have an SSE4.1 version of trunc / truncf (using this
instruction with operand 11); I'd expect one to make sense, but of
course it should be benchmarked against the existing C code. I'll
file a bug in Bugzilla for the lack of such a version.
Tested for x86_64.
[BZ #15479]
* sysdeps/x86_64/fpu/multiarch/s_ceil.S (__ceil_sse41): Set bit 3
of immediate operand to rounding instruction.
* sysdeps/x86_64/fpu/multiarch/s_ceilf.S (__ceilf_sse41):
Likewise.
* sysdeps/x86_64/fpu/multiarch/s_floor.S (__floor_sse41):
Likewise.
* sysdeps/x86_64/fpu/multiarch/s_floorf.S (__floorf_sse41):
Likewise.
This file is partially generated. To make updates a little
simpler, I have moved the generated code into a partially
contained header to simplify regeneration.
gen-tst-strtod-round.c now takes two, mandatory arguments.
These arguments specify the input test data and the output
destination, respectively.
C99 and C11 allow but do not require ceil, floor, round and trunc to
raise the "inexact" exception for noninteger arguments. TS 18661-1
requires that this exception not be raised by these functions. This
aligns them with general IEEE semantics, where "inexact" is only
raised if the final step of rounding the infinite-precision result to
the result type is inexact; for these functions, the
infinite-precision integer result is always representable in the
result type, so "inexact" should never be raised.
The generic implementations of ceil, floor and round functions contain
code to force "inexact" to be raised. This patch removes it for round
functions to align them with TS 18661-1 in this regard. The tests
*are* updated by this patch; there are fewer architecture-specific
versions than for ceil and floor, and I fixed the powerpc ones some
time ago. If any others still have the issue, as shown by tests for
round failing with spurious exceptions, they can be fixed separately
by architecture maintainers or others.
Tested for x86_64, x86 and mips64.
[BZ #15479]
* sysdeps/ieee754/dbl-64/s_round.c (huge): Remove variable.
(__round): Do not force "inexact" exception.
* sysdeps/ieee754/dbl-64/wordsize-64/s_round.c (huge): Remove
variable.
(__round): Do not force "inexact" exception.
* sysdeps/ieee754/flt-32/s_roundf.c (huge): Remove variable.
(__roundf): Do not force "inexact" exception.
* sysdeps/ieee754/ldbl-128/s_roundl.c (huge): Remove variable.
(__roundl): Do not force "inexact" exception.
* sysdeps/ieee754/ldbl-96/s_roundl.c (huge): Remove variable.
(__roundl): Do not force "inexact" exception.
* math/libm-test.inc (round_test_data): Do not allow spurious
"inexact" exceptions.
C99 and C11 allow but do not require ceil, floor, round and trunc to
raise the "inexact" exception for noninteger arguments. TS 18661-1
requires that this exception not be raised by these functions. This
aligns them with general IEEE semantics, where "inexact" is only
raised if the final step of rounding the infinite-precision result to
the result type is inexact; for these functions, the
infinite-precision integer result is always representable in the
result type, so "inexact" should never be raised.
The generic implementations of ceil, floor and round functions contain
code to force "inexact" to be raised. This patch removes it for floor
functions to align them with TS 18661-1 in this regard. Note that
some architecture-specific versions may still raise "inexact", so the
tests are not updated and the bug is not yet fixed.
Tested for x86_64, x86 and mips64.
[BZ #15479]
* sysdeps/ieee754/dbl-64/s_floor.c: Do not mention "inexact"
exception in comment.
(huge): Remove variable.
(__floor): Do not force "inexact" exception.
* sysdeps/ieee754/dbl-64/wordsize-64/s_floor.c: Do not mention
"inexact" exception in comment.
(huge): Remove variable.
(__floor): Do not force "inexact" exception.
* sysdeps/ieee754/flt-32/s_floorf.c: Do not mention "inexact"
exception in comment.
(huge): Remove variable.
(__floorf): Do not force "inexact" exception.
* sysdeps/ieee754/ldbl-128/s_floorl.c: Do not mention "inexact"
exception in comment.
(huge): Remove variable.
(__floorl): Do not force "inexact" exception.
C99 and C11 allow but do not require ceil, floor, round and trunc to
raise the "inexact" exception for noninteger arguments. TS 18661-1
requires that this exception not be raised by these functions. This
aligns them with general IEEE semantics, where "inexact" is only
raised if the final step of rounding the infinite-precision result to
the result type is inexact; for these functions, the
infinite-precision integer result is always representable in the
result type, so "inexact" should never be raised.
The generic implementations of ceil, floor and round functions contain
code to force "inexact" to be raised. This patch removes it for ceil
functions to align them with TS 18661-1 in this regard. Note that
some architecture-specific versions may still raise "inexact", so the
tests are not updated and the bug is not yet fixed.
Tested for x86_64, x86 and mips64.
[BZ #15479]
* sysdeps/ieee754/dbl-64/s_ceil.c: Do not mention "inexact"
exception in comment.
(huge): Remove variable.
(__ceil): Do not force "inexact" exception.
* sysdeps/ieee754/dbl-64/wordsize-64/s_ceil.c: Do not mention
"inexact" exception in comment.
(huge): Remove variable.
(__ceil): Do not force "inexact" exception.
* sysdeps/ieee754/flt-32/s_ceilf.c (huge): Remove variable.
(__ceilf): Do not force "inexact" exception.
* sysdeps/ieee754/ldbl-128/s_ceill.c: Do not mention "inexact"
exception in comment.
(huge): Remove variable.
(__ceill): Do not force "inexact" exception.
When --enable-bind-now is used to configure glibc build, we can avoid
an extra branch to the PLT entry by using indirect branch via the GOT
slot instead, which is similar to the first instructuon in the PLT
entry. Changes in the shared library sizes in text sections:
Shared library Before (bytes) After (bytes)
libm.so 1060813 1060797
libmvec.so 160881 160805
libpthread.so 94992 94984
librt.so 25064 25048
* config.h.in (BIND_NOW): New.
* configure.ac (BIND_NOW): New. Defined for --enable-bind-now.
* configure: Regenerated.
* sysdeps/x86_64/sysdep.h (JUMPTARGET)[BIND_NOW]: Defined to
indirect branch via the GOT slot.
There exist optimized memcpy functions on s390, but no optimized mempcpy.
This patch adds mempcpy entry points in memcpy.S files, which
use the memcpy implementation. Now mempcpy itself is also an IFUNC function
as memcpy is and the variants are listed in ifunc-impl-list.c.
The s390 string.h does not define _HAVE_STRING_ARCH_mempcpy.
Instead mempcpy string/string.h inlines memcpy() + n.
If n is constant and small enough, GCC emits instructions like mvi or mvc
and avoids the function call to memcpy.
If n is not constant, then memcpy is called and n is added afterwards.
If _HAVE_STRING_ARCH_mempcpy would be defined, mempcpy would be called in
every case.
According to PR70140 "Inefficient expansion of __builtin_mempcpy"
(https://gcc.gnu.org/bugzilla/show_bug.cgi?id=70140) GCC should handle a
call to mempcpy in the same way as memcpy. Then either the mempcpy macro
in string/string.h has to be removed or _HAVE_STRING_ARCH_mempcpy has to
be defined for S390.
ChangeLog:
[BZ #19765]
* sysdeps/s390/mempcpy.S: New File.
* sysdeps/s390/multiarch/mempcpy.c: Likewise.
* sysdeps/s390/multiarch/Makefile (sysdep_routines): Add mempcpy.
* sysdeps/s390/multiarch/ifunc-impl-list.c (__libc_ifunc_impl_list):
Add mempcpy variants.
* sysdeps/s390/s390-32/memcpy.S: Add mempcpy entry point.
(memcpy): Adjust to be usable from mempcpy entry point.
(__memcpy_mvcle): Likewise.
* sysdeps/s390/s390-64/memcpy.S: Likewise.
* sysdeps/s390/s390-32/multiarch/memcpy-s390.S: Add entry points
____mempcpy_z196, ____mempcpy_z10 and add __GI_ symbols for mempcpy.
(__memcpy_z196): Adjust to be usable from mempcpy entry point.
(__memcpy_z10): Likewise.
* sysdeps/s390/s390-64/multiarch/memcpy-s390x.S: Likewise.
On s390, the memcpy, memcmp, memset functions are IFUNC symbols,
which are created with s390_libc_ifunc-macro.
This macro creates a __GI_ symbol which is set to the
ifunced symbol. Thus calls within libc.so to e.g. memcpy
result in a call to *ABS*+0x954c0@plt stub and afterwards
to the resolved memcpy-ifunc-variant.
This patch sets the __GI_ symbol to the default-ifunc-variant
to avoid the plt call. The __GI_ symbols are now created at the
default variant of ifunced function.
ChangeLog:
* sysdeps/s390/multiarch/ifunc-resolve.h (s390_libc_ifunc):
Remove __GI_ symbol.
* sysdeps/s390/s390-32/multiarch/memcmp-s390.S: Add __GI_memcmp symbol.
* sysdeps/s390/s390-64/multiarch/memcmp-s390x.S: Likewise.
* sysdeps/s390/s390-32/multiarch/memcpy-s390.S: Add __GI_memcpy symbol.
* sysdeps/s390/s390-64/multiarch/memcpy-s390x.S: Likewise.
* sysdeps/s390/s390-32/multiarch/memset-s390.S: Add __GI_memset symbol.
* sysdeps/s390/s390-64/multiarch/memset-s390x.S: Likewise.
The __memcpy_default variant on s390 64bit calculates the number of
256byte blocks in a 64bit register and checks, if they exceed 1MB
to jump to mvcle. Otherwise a mvc-loop is used. The compare-instruction
only checks a 32bit value.
This patch uses a 64bit compare.
ChangeLog:
* sysdeps/s390/s390-64/memcpy.S (memcpy):
Use cghi instead of chi to compare 64bit value.
If more than 255 bytes should be copied, the algorithm jumps away.
Before this patch, it jumps to the mvc-loop (.L_G5_12).
Now it jumps first to the "> 1MB" check, which jumps away to
__memcpy_mvcle. Otherwise, the mvc-loop (.L_G5_12) copies the bytes.
ChangeLog:
* sysdeps/s390/s390-32/memcpy.S (memcpy):
Jump to 1MB check before executing mvc-loop.
After the heap rewriting added in commit
4cf6c72fd2 (malloc: Rewrite dumped heap
for compatibility in __malloc_set_state), we can change malloc alignment
for new allocations because the alignment of old allocations no longer
matters.
We need to increase the malloc state version number, so that binaries
containing dumped heaps of the new layout will not try to run on
previous versions of glibc, resulting in obscure crashes.
This commit addresses a failure of tst-malloc-thread-fail on the
affected architectures (32-bit ppc and mips) because the test checks
pointer alignment.
The call is technically in a loop, and under certain circumstances
(which are quite difficult to reproduce in a test case), alloca
can be invoked repeatedly during a single call to clntudp_call.
As a result, the available stack space can be exhausted (even
though individual alloca sizes are bounded implicitly by what
can fit into a UDP packet, as a side effect of the earlier
successful send operation).
This avoids aliasing issues with GCC 6 in -fno-strict-aliasing
mode. (With implicit padding, not all data is copied.)
This change makes it explicit that struct sockaddr_storage is
only 126 bytes large on m68k (unlike elsewhere, where we end up
with the requested 128 bytes). The new test case makes sure that
this does not happen on other architectures.
The conform/ test of limits.h namespace for XPG3 was failing because
of NL_* and NZERO defines. Those symbols are EX-shaded, not
UX-shaded, so it's correct for them to be defined for XPG3; this patch
corrects the expectations accordingly. (Actually it looks like they
should not be listed as optional for these standards, but that's
another matter.)
Tested for x86_64 and x86.
* conform/data/limits.h-data (CHARCLASS_NAME_MAX): Also expect for
[XPG3 || XPG4].
(NL_ARGMAX): Also expect for [XPG3].
(NL_LANGMAX): Likewise.
(NL_MSGMAX): Likewise.
(NL_NMAX): Likewise.
(NL_SETMAX): Likewise.
(NL_TEXTMAX): Likewise.
(NZERO): Likewise.
(TMP_MAX): Likewise.
* conform/Makefile (test-xfail-XPG3/limits.h/conform): Remove
variable.
This patch updates sysdeps/unix/sysv/linux/bits/socket.h for new
constants added in Linux 4.6. AF_KCM / PF_KCM are added. SOL_KCM is
new, and I added a lot of SOL_* values postdating the last one present
in the header, since I saw no apparent reason for the set in glibc to
stop at SOL_IRDA. MSG_BATCH is added; Linux also has
MSG_SENDPAGE_NOTLAST which is not in glibc, but given the comment
starts "sendpage() internal" I presume it's correct for it not to be
in glibc.
(Note that this is a case where the Linux kernel header with userspace
relevant values is *not* a uapi header but include/linux/socket.h - I
don't know why, but at least this header, as well as uapi headers,
needs reviewing for glibc-relevant changes each release.)
Tested for x86_64 and x86 (testsuite, and that installed stripped
shared libraries are unchanged by the patch).
* sysdeps/unix/sysv/linux/bits/socket.h (PF_KCM): New macro.
(PF_MAX): Update value.
(AF_KCM): New macro.
(SOL_NETBEUI): Likewise.
(SOL_LLC): Likewise.
(SOL_DCCP): Likewise.
(SOL_NETLINK): Likewise.
(SOL_TIPC): Likewise.
(SOL_RXRPC): Likewise.
(SOL_PPPOL2TP): Likewise.
(SOL_BLUETOOTH): Likewise.
(SOL_PNPIPE): Likewise.
(SOL_RDS): Likewise.
(SOL_IUCV): Likewise.
(SOL_CAIF): Likewise.
(SOL_ALG): Likewise.
(SOL_NFC): Likewise.
(SOL_KCM): Likewise.
(MSG_BATCH): New enum value and macro.
L2 cache is shared by 2 cores on Knights Landing, which has 4 threads
per core:
https://en.wikipedia.org/wiki/Xeon_Phi#Knights_Landing
So L2 cache is shared by 8 threads on Knights Landing as reported by
CPUID. We should remove special L2 cache case for Knights Landing.
[BZ #18185]
* sysdeps/x86/cacheinfo.c (init_cacheinfo): Don't limit threads
sharing L2 cache to 2 for Knights Landing.
This patch corrects various conformtest expectations in ftw.h for XPG3
and XPG4.
Tested for x86_64 and x86.
* conform/data/ftw.h-data (struct FTW): Do not expect for [XPG3].
(FTW_DP): Do not expect for [XPG3 || XPG4].
(FTW_SL): Do not expect for [XPG3].
(FTW_SLN): Likewise.
(FTW_PHYS): Likewise.
(FTW_MOUNT): Likewise.
(FTW_DEPTH): Likewise.
(FTW_CHDIR): Likewise.
(nftw): Likewise.
* conform/Makefile (test-xfail-XPG3/ftw.h/conform): Remove
variable.
ldbl-128ibm had an implementation of fmal that just did (x * y) + z in
most cases, with no attempt at actually being a fused operation.
This patch replaces it with a genuine fused operation. It is not
necessarily correctly rounding, but should produce a result at least
as accurate as the long double arithmetic operations in libgcc, which
I think is all that can reasonably be expected for such a non-IEEE
format where arithmetic is approximate rather than rounded according
to any particular rule for determining the exact result. Like the
libgcc arithmetic, it may produce spurious overflow and underflow
results, and it falls back to the libgcc multiplication in the case of
(finite, finite, zero).
This concludes the fixes for bug 13304; any subsequently found fma
issues should go in separate Bugzilla bugs. Various other pieces of
bug 13304 were fixed in past releases over the past several years.
Tested for powerpc.
[BZ #13304]
* sysdeps/ieee754/ldbl-128ibm/s_fmal.c: Include <fenv.h>,
<float.h>, <math_private.h> and <stdlib.h>.
(add_split): New function.
(mul_split): Likewise.
(ext_val): New typedef.
(store_ext_val): New function.
(mul_ext_val): New function.
(compare): New function.
(add_split_ext): New function.
(__fmal): After checking for Inf, NaN and zero, compute result as
an exact sum of scaled double values in round-to-nearest before
adding those up and adjusting for other rounding modes.
* math/auto-libm-test-in: Remove xfail-rounding:ldbl-128ibm from
tests of fma.
* math/auto-libm-test-out: Regenerated.
Intel CPUID with EAX == 11 returns:
ECX Bits 07 - 00: Level number. Same value in ECX input.
Bits 15 - 08: Level type.
^^^^^^^^^^^^^^^^^^^^^^^^ This is level type.
Bits 31 - 16: Reserved.
Intel processor level type mask should be 0xff00, not 0xff0.
[BZ #20119]
* sysdeps/x86/cacheinfo.c (init_cacheinfo): Correct Intel
processor level type mask for CPUID with EAX == 11.
Skip counting logical threads for Intel processors if the HTT bit is 0
which indicates there is only a single logical processor.
* sysdeps/x86/cacheinfo.c (init_cacheinfo): Skip counting
logical threads if the HTT bit is 0.
* sysdeps/x86/cpu-features.h (bit_cpu_HTT): New.
(index_cpu_HTT): Likewise.
(reg_HTT): Likewise.
X86-64 memset-vec-unaligned-erms.S aligns many jump targets, which
increases code sizes, but not necessarily improve performance. As
memset benchtest data of align vs no align on various Intel and AMD
processors
https://sourceware.org/bugzilla/attachment.cgi?id=9277
shows that aligning jump targets isn't necessary.
[BZ #20115]
* sysdeps/x86_64/multiarch/memset-vec-unaligned-erms.S (__memset):
Remove alignments on jump targets.
This patch corrects some conformtest expectations for pwd.h for XPG4.
Tested for x86_64 and x86.
* conform/data/pwd.h-data (endpwent): Do not expect for [XPG3].
(getpwent): Likewise.
(setpwent): Likewise.
* conform/Makefile (test-xfail-XPG3/pwd.h/conform): Remove
variable.
This patch corrects some conformtest expectations for search.h for
XPG3.
Tested for x86_64 and x86.
* conform/data/search.h-data (insque): Do not expect for [XPG3].
(remque): Likewise.
* conform/Makefile (test-xfail-XPG3/search.h/conform): Remove
variable.
libm-test.inc has a comment about signs of NaNs not being tested.
This is out of date since:
commit ce66581742
Author: Joseph Myers <joseph@codesourcery.com>
Date: Sat Nov 16 12:48:35 2013 +0000
Test signs of NaNs in libm-test.inc where appropriate.
This patch removes the inaccurate statement.
* math/libm-test.inc: Update comment not to refer to signs of NaNs
not being tested.
There is no need to call the internal funtion, _Unwind_Resume, which
is defined in unwind-forcedunwind.c, via PLT.
* sysdeps/unix/sysv/linux/x86_64/pthread_cond_timedwait.S
(__condvar_cleanup2): Remove JUMPTARGET from _Unwind_Resume
call.
* sysdeps/unix/sysv/linux/x86_64/pthread_cond_wait.S
(__condvar_cleanup1): Likewise.
Add PTHREAD_UNWIND to replace JUMPTARGET(__pthread_unwind) and define
it to __GI___pthread_unwind within libpthread.
* sysdeps/unix/sysv/linux/x86_64/cancellation.S (PTHREAD_UNWIND):
New
(__pthread_unwind): Renamed to ...
(PTHREAD_UNWIND): This.
(__pthread_enable_asynccancel): Replace
JUMPTARGET(__pthread_unwind) with PTHREAD_UNWIND.
This patch adds CLONE_NEWCGROUP, new in Linux 4.6, to
sysdeps/unix/sysv/linux/bits/sched.h.
Tested for x86_64 and x86 (testsuite, and that installed stripped
shared libraries are unchanged by the patch).
* sysdeps/unix/sysv/linux/bits/sched.h [__USE_GNU]
(CLONE_NEWCGROUP): New macro.
This patch adds Q_GETNEXTQUOTA, new in Linux 4.6, to
sysdeps/unix/sysv/linux/sys/quota.h.
Tested for x86_64 and x86 (testsuite, and that installed shared
libraries are unchanged by the patch).
* sysdeps/unix/sysv/linux/sys/quota.h [_LINUX_QUOTA_VERSION >= 2]
(Q_GETNEXTQUOTA): New macro.
Clear the destination buffer updated by the previous run in bench-memcpy.c
and test-memcpy.c to catch the error when the following implementations do
not copy anything.
[BZ #19907]
* benchtests/bench-memcpy.c (do_one_test): Clear the destination
buffer updated by the previous run.
* string/test-memcpy.c (do_one_test): Likewise.
* benchtests/bench-memmove.c (do_one_test): Add a comment.
* string/test-memmove.c (do_one_test): Likewise.
